- On sale!

Reference: DWM14042301
Spring antenna is specialized for wireless data transmission. This antenna with good performance of V.S.W.R, small size design, easily installation, stable performance and good anti-shock and anti-aged compatible for Hoperf Modules.
Reference: DWM14032902
SMA rf antenna connector is pallets copper gold andexternal thread needle sma pallets plate rf connector.
Reference: DWM14032102
Whip antenna for sub-1 GHz, 433MHz,868MHz and 915MHz with SMA male connectors.it's used with wireless module recommanded by Hoperf .
Reference: DWM14042401
SMA RG178 extension female cable for GPS, GSM antenna,RF module, SMA cable,IPEX to SMA jumper cable.
Reference: DWM18032302
USD3.0/pcs MOQ100pcs LoRa Antenna designed for Lora application which required for outdoor waterproof highgain and work at ISM free band like 433MHz /868MHz /915MHz SMA Male Whip antenna.
Reference: DWM16121503
DWM-TLB-3.0QB SUB-1GHz / 2.4GHz Whip antenna with a Collapsible SMA male connectors.Which are available for 433MHz,868MHz.915MHz and 2.4GHz..
Reference: DWM17111002
LoRa Antenna-433MHz High Gain internal aerial piamater FPC Antenna with IPEX connctor.
Reference: DWM15101001
Brand: Semtech
RFM50 module series’ design is based on the high performance RF50 SoC chip, It include a CIP-51 core‘ MCU and 100mW transceiver. It operate at 433/470/868/915 MHz ISM band, comply with FCC, ETSI regulation.
RAK811 WisNode LoRa Module development board is compatible with Arduino Development Board. It can also be used as an extension board development with Arduino.
WisNode-LoRa RAK811 /RAK812 LoRa Arduino shield Support AS923, 868/915MHz, LoRa/TTN, Open source LoRa development board.
The following image is RAK WisNode-Lora development board,and it compatible Arduino development board, It also can be used as an extension board development with Arduino. The interface resource are as follow:
Function | Name | Description |
---|---|---|
Module | U3 | RAK811 Lora module |
External Interface | Micro USB | Power Supply; DC 5V Input,USB to TTL communication interface |
Key | Reset | Module Reset Key |
Leading Foot | P1 | Boot Switch Pin,When Boot Pin Switch to 3.3V Module will into the Boot Mode |
P4 | Debug Pin | |
P5 | Uart Switch Pin | |
Power Test | J1 | Module Power Test Pin |
LED Indicator | LED1(Power) | Power Indicator Light |
Connect the evaluation board to the computer via the Micro USB line, Through the computer serial port tool to send commands to the module.As shown in the following figure:
at+mode=0 /* SET LoraWAN work mode */ OK at+get_config=dev_eui /* GET Dev_EUI check */ OK3037343644357402 at+set_config=app_eui:39d7119f920f7952&app_key:a6b08140dae1d795ebfa5a6dee1f4dbd /* SET LoraGateway app_eui and app_key , big endian*/ OK at+join=otaa /* Join OTAA type*/ OK at+recv=3,0,0 /* Join status success*/
Welcome to RAK811 at+mode=0 /* SET LoraWAN work mode */ OK at+set_config=dev_addr:00112233&nwks_key:3432567afde4525e7890cfea234a5821& apps_key:a48adfc393a0de458319236537a11d90 /* SET LoraGateway dev_addr nwks_key and apps_key , big endian*/ OK at+join=abp /* Join ABP type*/ OK
/*After join gateway success, then can send and receive data*/ at+send=0,2,000000000000007F0000000000000000 /*APP port:2, battery level 50%, unconfirmed message*/ at+recv=2,0,0 /*unconfirmed mean tx success*/ at+send=1,2,000000000000007F0000000000000000 /*APP port :2, battery level 50%, confirmed message*/ at+recv=1,0,0 /*confirmed mean receive ack from gateway*/ /*If gateway has data to send module, will receive date meanwhile ack */ at+recv=0,2,10,30313233343536373839 /*APP port :2, receive size 10, hex:30313233343536373839*/
/* Module A Rx Side*/ Welcome to RAK811 at+mode=1 /* SET LoraP2P work mode */ OK at+rf_config=867700000,10,0,1,8,14 /* SET LoraP2P Frequency:867.7MHz, SF10,Bandwith 125KHz, coding Rate:4/5, Preamlen:8, tx power:14dbm */ OK at+rxc=1 /* SET LoraP2P Rx continue enable report rx data */ OK at+rx_stop /* If want stop Rx continue */
/* Module B Tx Side*/ Welcome to RAK811 at+mode=1 /* SET LoraP2P work mode */ OK at+rf_config=867700000,10,0,1,8,14 /* SET LoraP2P Frequency:867.7MHz, SF10,Bandwith 125KHz, coding Rate:4/5, Preamlen:8, tx power:14dbm */ OK at+txc=100,1000,800100000600010002da9557e142d9 /* SET LoraP2P Tx continue ,100 packets, 1S interval, hex data */ OK at+recv=9,0,0 /*When Tx complete */ at+tx_stop /* If want stop Tx continue */
To upgrade the Lora module, First we should make the module get into Boot mode. We should switch the P1 pin make the Boot pin connection with 3.3V Pin. Then reset the module, Operate according to the steps:
1.Open the Flash Loader Demonstrator tool,Set the serial port parameters;
2.Click the “NEXT” button, arrive the following interface;
3.The again the “Next” button,Choose STM32L1_Cat2-128K;
4.Choose “Download to device”,Set the path to the new firmware, and click “NEXT” button;
5.Upgrading;
6.Upgrade Successful.
Reference: DWM17102702
LoRa Antenna designed for Lora application which required for outdoor waterproof highgain and work at ISM free band like 433MHz /868MHz /915MHz SMA Male Whip antenna.
Reference: DWM18011701
RAK811 LoRa module complies with the latest LoRaWAN Class A & C protocol specifications, it is simple to access LWPA IOT platforms integrates SX1276 and stm32L with TELEC CE FCC KCC certification.
Reference: DWM18011801
DWM-RAK83 433MHz/ 868MHz/ 915MHz SX1301 LoRa/ LoRaWAN Gateway Module combine a host system like Raspberry Pi or WisAP(OpenWRT based) or WisCam to help you realize the whole Lora system development.
Reference: DWM20052801
The DWM-RAK7204 is an LPWAN node that serves as an environmental monitoring station. The high-precision sensors, can measure changes in temperature, humidity, gas pressure and provide an indoor air quality index.
Reference: DWM18122601
DWM-RAK5205 LoRa Tracker built on SX1276 LoRaWAN modem with low power micro-controller STM32L1, integrated the GPS module is an open all source code products,allowing users to conveniently link to the LoRaWAN network.
Reference: DWM22022502
RAK2287 /RAK5146 Pi HAT is a converter board with a Raspberry Pi form factor that enables the RAK2287 and RAK5146 LPWAN concentrator module to be mounted on the top of the Raspberry Pi.
Reference: DWM20061601
Brand: Semtech
DWM-RAK4200 LPWAN Evaluation Board is a WisBlock product consisting of RAK4200 LPWAN Module and RAK5005 WisBase includes an STM32L071 MCU and SX1276 LoRa® chip that complies with the LoRaWAN® 1.0.2 protocols.
Reference: DWM19022402
DWM-RAK7249 is The Enterprise DIY outdoor LoRaWan GATEWAY Builtin OpenWRT OS support 8 channels LoRa/4G/WIFI/GPS .
Reference: DWM20060102
Brand: Semtech
DWM-RAK4200 Breakout Module is specifically designed to allow easy excess to the pins on the module in order to simplify development and testing.it's utilized is of an Xbee form factor.
Reference: DWM19091701
DWM-RAK2245 SX1301 8 Channels Stamp Edition is a LoRaWAN gateway Module based on SX1301,Pre-install LoRa gatewayOS.
Reference: DWM22061601
RAK10700 is a GNSS Tracker device with a GNSS modem providing LPWAN and BLE communication using the nRF52 MCU and SX1262 LoRa transceiver of the RAK4631 Core module.
Reference: DWM19091702
RAK2247 LoRa Gateway mPCIE Board-RAK833 Concentrator Module is the evolution of RAK833 is a LoRaWAN gateway Module based on SX1301,Pre-install LoRa gateway OS.
Reference: DWM20053001
Brand: Semtech
DWM-RAK4600 LPWAN Module includes an nRF52832 MCU and an SX1276 LoRa® chip. It has an ultra-low power consumption of 2.0uA in sleep mode, high LoRa® output power up to 20dB max in work mode, and BLE output power up to 4dBm.
Reference: DWM20053103
Brand: Semtech
The DWM-RAK4600 development board allows access to all serial and GPIO ports for easy configuration. The RAK4600 core module includes nRF52832 MCU and SX1276 LoRa® chip to help you quickly and easily develop/test your firmware.
Reference: DWM22062301
The LoRaWAN GNSS GPS Tracker is with a sensor to detect location change every set time interval and with solar panel built-in on the enclosure Use this kit for tracking and monitoring cargo, vehicles, and marine vessels.
Reference: DWM18011702
RAK811 Development Kit WisDuo LoRa Module is a combination of the RAK811 chipset and the RAK811 Breakout Board.
Reference: DWM20053104
Brand: Semtech
DWM-RAK4260 Breakout Module is specifically designed to allow easy excess to the pins on the module in order to simplify development and testing.
Reference: DWM19070803
RAK7258 Micro Gateway is a full 8-channel LoRa Gateway with built-in Ethernet connectivity for a straightforward setup. Additionally, there is an onboard Wi-Fi setup that allows it to be easily configured via the default Wi-Fi AP mode.
Reference: DWM19030101
DWM-RAK7243 Pilot Gateway Pro Kit with Cellular & GPS modules for PoC Raspberry Pi 3B+, RAK2245 Pi HAT,RAK2013 Cellular Pi HAT.
RAK811 WisNode LoRa Module development board is compatible with Arduino Development Board. It can also be used as an extension board development with Arduino.