Reference: DWM17010902

2x40 Pin 2.54mm Female Header

2x40 Pin 2.54mm Female Header Can be cut to size with a pair of wire-cutters. Standard 2.54mm spacing. They mate very well with male pin headers.

Reference: DWM17010901

2x40 Pin 2.54mm Male Header

2x40 Pin 2.54mm Male Header is 2.54mm Pitch header it's quite for the beak board convert from SMT to DIP pack.

Reference: DWM16092102

3DTouch auto leveling sensor for 3D printer

3DTouch features simple, smart and precise. It could work with nearly any kind of bed materials, such as glasses, woods, metals and so on.

Reference: DWM16122005

A6 GPRS/ GSM Low-cost Shield board

This is a A6 GPRS/GSM Shield, which is use the newest A6 gprs/gsm module, A6 is a low-cost but efficient chip. With its ultra-small size, low power consumption and wide operating temperature range.

Reference: DWM02030406

A9G GPRS /GSM /GPS Pudding/SMS/Voice/ Positioning IOT Development Board

The A9G development board is a multifunctional development board based on EMC’s A9G GPRS/ GSM + GPS/ BDS module it can be used Wireless Data Transmission and Positioning IOT Development.

Reference: DWM14032106

Arduino uno R3

The Arduino Uno Rev3 is a microcontroller board based on the ATmega328.

Reference: DWM19121101

ATmega328P LoRa Radio Node Sx1276 / Sx1278 same as the Arduino pro mini IoT end nodes

ATmega328P LoRa Radio Node is based on SX1276/SX1278 which use the Arduino pro mini 8Mhz 3.3V bootloader, usage same as the Arduino pro mini.

Reference: DWM14041801

CoLinkEx_V1.1 hardware debugging adapter

CoLinkEx is a hardware debugging adapter which supports JTAG & SW debugging with ARM Cortex M devices in CooCox software and Keil RealView MDK.

Reference: DWM17072502

D-duino ESP8266 IOT WiFi NodeMCU Board with 0.96OLED

D-duino is a combination of ESP8266 and OLED is a 6 IOT WiFi NodeMCU Development Board .

Reference: DWM14120304

DHT22 AM2302 Digital Temperature And Humidity Sensor

DHT22 AM2302 Low cost  Digital Temperature And Humidity Sensor Replace SHT11 SHT15.

Reference: DWM15090901

DWM-2WD Arduino UNO based Smart Car Kit

DWM-2WD Smart Car Kit is an kit base on the Arduino UNO with Bluetooth Control.

Reference: DWM20030404

DWM-32u4 LoRa IOT board for Wireless remote control telemetry remote communication equipment and robot control

The DWM-32u4 with LoRa RFM95 IOT Board consists of the mega24u and the wireless transport module RFM95 is used in remote control, telemetry, remote communication equipment, robot control, wireless communications.

Reference: DWM18121803

DWM-51WS3 APRS weather station EVB board

DWM-51WS3 is high precision meteorological measurement module, which support to measure wind direction, wind speed, rainfall, temperature, humidity, pressure measurement mode, secondary development output with APRS data.

Reference: DWM14072802

DWM-APC220-433MHz /470MHz Data Link module

APC220 433MHz / 470MHz Wireless Data Transmission Transceiver, Transparent data link rf module.

Reference: DWM14080101

Brand: Semtech

DWM-APC320 SI4463 433MHz/ 868MHz/ 915MHz Long range data link rf module

APC320 is built in the SI4463 RFIC which can work at 433/ 868/ 915MHz TTL/UART, RS232, RS485, 20dBm(optional), Data Link module, which can cover 2000meters.

Reference: DWM15100301

DWM-BNC BNC Female to SMB female inner hole 50ohm RG316 extension jumper cable

BNC Female to SMB female inner hole 50ohm Rf coaxial connector Switch wiring RG316  extension jumper cable and wire length can be customized. 

Reference: DWM15100201

DWM-BNC BNC Male /Female RF coaxial connector for 50-3 (5 mm) coaxial cable

DWM-BNC BNC-JC-3 BNC male /Female RF coaxial connector for 50-3 (5 mm) coaxial cable.

Reference: DWM15100205

DWM-BNC BNC Male to BNC Male 50ohm RG316 extension jumper cable

BNC Male to BNC Male 50ohm Rf coaxial connector Switch wiring RG316  extension jumper cable and wire length can be customized.

Reference: DWM18102203

DWM-BNC Male to SMA male 50ohm RF coaxial RG58 extension jumper cable

DWM-BNC Male to SMA male  50ohm Rf coaxial connector Switch wiring RG58  extension jumper cable and wire length which can be customized.

Reference: DWM18101708

DWM-BNC-J Male to TNC-J Male 50ohm RF coaxial RG58 extension jumper cable

DWM-BNC-J Male to TNC-J Male to Male 50ohm Rf coaxial connector Switch wiring RG58  extension jumper cable and wire length which can be customized.