All best sellers
  • -$0.50
3DTouch auto leveling sensor for 3D printer
  • 3DTouch auto leveling sensor for 3D printer
  • 3DTouch auto leveling sensor for 3D printer
  • 3DTouch auto leveling sensor for 3D printer
  • 3DTouch auto leveling sensor for 3D printer
  • 3DTouch auto leveling sensor for 3D printer
  • 3DTouch auto leveling sensor for 3D printer
  • 3DTouch auto leveling sensor for 3D printer

3DTouch auto leveling sensor for 3D printer

DWM16092102

3DTouch features simple, smart and precise. It could work with nearly any kind of bed materials, such as glasses, woods, metals and so on.

Volume discounts

Quantity Unit discount You Save
5 $1.00 Up to $5.00
10 $2.00 Up to $20.00
20 $3.00 Up to $60.00
$45.00
$44.50 Save $0.50
Quantity

Description

Features: 

1 Simple

3DTouch can be easily applied, since it has a small and simple structure. Gathering information & firmware setting will be an easy task, because 3DTouch works as usual auto bed leveling sensor.

2 Smart

Self-test: The push pin is operated three times to test when the power is on Alarm: The LED light blinks if a problem found on a self-test or on an operation 

3 High-precision 

3DTouch’s Standard Deviation in repeatability is around 0.005mm, at that precise. If you choose 3DTouch, your 3D printer will be high-class masterpiece, giving you an enjoyable experience.

4. Innovative Solenoid: Ultra Power Saving

On idle state, while the push-pin is whether pulled out or retracted, there are not any electric current flowing on solenoid, and standby electric current in the whole device is below 15mA on average, whereas on working state, while the pin is moving in sudden about 100ms, under 300mA flows in the device. Low power consumption even further drops joule heating, preventing from heat problem.

5 Technologies 

3DTouch consists of Atmel ATtiny13A, solenoid, and a push pin.

6 wide Selection of Bed

3DTouch does not uses either optical, nor proximity (inductive/capacitive) sensor. 3DTouch is controlled by Hall Effect, providing high precision. Thus the bed material can be selected freely.

7 Optimized structure:  Larger Build Size

3DTouch is a small and technology-intensive one. Build size can be set larger than other existing auto bed leveling sensor.

3DTouch uses existing RC Servo motor signal intactly, so just plug 3DTouch on the same pins after removing servo motor.

 For more detailed information, please refer to wiki.

Specification

Voltage: 5V

Current: 15mA

Max. Current: 300mA

Cable length: 150mm

Net Weight: 10g

Shipping weight: 25g

Operate condition

3DTouch can be operated in the following condition.

One I/O for control (PWM or Software PWM)

One I/O for Z min (Z Probe)

GND and +5V power

Wiring

3-pin: Brown (-, GND), Red (+5V), Orange (control signal)

2-pin: Black (-, GND), White (Z min)

Caution 

Additional power supply will be needed in case your board does not supply enough amperage.

Electronic devices can be damaged or even destroyed if connected to wrong polarity. [wrong terminal connect to 5V(+) and GND(-)]

Pulling/pushing hard on the push-pin can damage 3DTouch and make it less accurate.

Fix push-pin with locking paint after reassembling or adjusting core.

Do not remove or deform elastic material attached on the push-pin.

Package List

1 X 3DTouch Auto leveling sensor     

1 X 3Pin Straight Pin

1 X 2Pin Straight Pin

2 X Screw & Nut & Washer 

2 X Dupont Housing Shell 3Pin

2 X Dupont Housing Shell 2Pin  

3 X Dupont Housing Shell 1Pin      

14 X Dupont Terminal

1 X 10KΩ 1/8W Resistor  

Useful Link:

3DTouch auto leveling sensor User Manual.pdf
3DTouch auto leveling sensor-1.zip
3DTouch mount for Geeetech prusa I3 pro X.zip

Product Details
DWM16092102
80 Items
You might also like
2 other products in the same category:

Reviews

Write your review

3DTouch auto leveling sensor for 3D printer

3DTouch features simple, smart and precise. It could work with nearly any kind of bed materials, such as glasses, woods, metals and so on.

Write your review

Follow us on Facebook