Reference: DWM14042301
Spring antenna is specialized for wireless data transmission. This antenna with good performance of V.S.W.R, small size design, easily installation, stable performance and good anti-shock and anti-aged compatible for Hoperf Modules.
Reference: DWM14032902
SMA rf antenna connector is pallets copper gold andexternal thread needle sma pallets plate rf connector.
Reference: DWM14032102
Whip antenna for sub-1 GHz, 433MHz,868MHz and 915MHz with SMA male connectors.it's used with wireless module recommanded by Hoperf .
Reference: DWM14042401
SMA RG178 extension female cable for GPS, GSM antenna,RF module, SMA cable,IPEX to SMA jumper cable.
Reference: DWM18032302
USD3.0/pcs MOQ100pcs LoRa Antenna designed for Lora application which required for outdoor waterproof highgain and work at ISM free band like 433MHz /868MHz /915MHz SMA Male Whip antenna.
Reference: DWM16121503
DWM-TLB-3.0QB SUB-1GHz / 2.4GHz Whip antenna with a Collapsible SMA male connectors.Which are available for 433MHz,868MHz.915MHz and 2.4GHz..
Reference: DWM17111002
LoRa Antenna-433MHz High Gain internal aerial piamater FPC Antenna with IPEX connctor.
Reference: DWM15101001
Brand: Semtech
RFM50 module series’ design is based on the high performance RF50 SoC chip, It include a CIP-51 core‘ MCU and 100mW transceiver. It operate at 433/470/868/915 MHz ISM band, comply with FCC, ETSI regulation.
LoRa32u4 RA02 is a light and low consumption board based on the Atmega32u4 and SX1278 433MHz LoRA module.
LoRa32u4 is a light and low consumption board based on the Atmega32u4 and 433MHz LoRA module RA02 from AI-Thinker and an USB battery charging circuit. Ideal for creating long range wireless networks that can exceed 2.4 GHz 802.15.4 and similar, it is more flexible than Bluetooth LE, does not require high power unlike WiFi and offers long range.
The RA02 LoRa module is fitted with an U.FL (IPX) external antenna connector.
The ATmega32u4 is clocked at 8 MHz and 3.3 V. This chip has 32 K of flash, 2 K of RAM and built-in USB to Serial communication, debugging and programming capabilities without the need for an external FTDI chip, it can also act as an HID device (mouse, keyboard, USB MIDI device, etc).
This board is also equipped with a LiPo and Liion charging circuit and a standard battery interface. It is fully compatible with Arduino. A white user led is tied to pin 13. An orange LED is used for charging status.
ATmega32u4 @ 8MHz with 3.3V logic/power
3.3V regulator with 500mA peak current output
USB native support, comes with USB bootloader and serial port debugging
20 GPIOs
Hardware Serial, hardware I2C, hardware SPI support
Built in 100mA lipoly charger with charging status indicator LED
Power/enable pin
4 mounting holes
Reset button
SX1278 RA02 LoRa® based module with SPI interface
8 x PWM pins
10 x analog inputs
Packet radio with ready-to-go Arduino libraries
License-free ISM bands (ITU "Europe" @ 433MHz)
+5 to +20 dBm up to 100 mW Power Output Capability (selectable in software)
~300uA during full sleep
~120mA peak during +20dBm transmit
~40mA during active radio listening.
U.FL (IP) antenna connector
Datasheet MPC73831
Datasheet RA02
Datasheet SX1278
Arduino code link
Package includes:
1 X LoRa32U4
Reference: DWM16011801
Brand: Semtech
LoRa1276 Wireless Transceiver Module adopts Semtech RF transceiver chip SX1276 which LOS transmission distance can reach to 4km~6km Long Distance.
Reference: DWM16092701
RFM98PW/ RFM95PW which are Enhanced Power Long Range Transceiver Module.the available versions is RFM98PW 433MHz, and 868MHz,915MHz for RFM95PW.
Reference: DWM16122201
The 433MHz /868MHz /915MHz Arduino LoRa Shield is a long range transceiver on a Arduino shield form factor and based on Open source library.Compatible with Arduino Leonardo, Uno, Mega, DUE.
Reference: DWM17110904
Spring-Antenna 433MHz /470MHz 3dbi Gain with IPEX Connector extension cable
Reference: DWM17120401
LoRa32u4 II is a light and low consumption board based on the Atmega32u4 and SX1276 868MHZ /915MHz LoRA module.
Reference: DWM19062801
ESP32-WROOM-32D and ESP32-WROOM-32U are powerful, generic Wi-Fi+BT+BLE MCU modules that target a wide variety of applications, ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streaming and MP3 decoding.
Reference: DWM20053103
Brand: Semtech
The DWM-RAK4600 development board allows access to all serial and GPIO ports for easy configuration. The RAK4600 core module includes nRF52832 MCU and SX1276 LoRa® chip to help you quickly and easily develop/test your firmware.
Reference: DWM20072902
The LDDS75 LoRaWAN Distance Detection Sensor node is a distance detection sensor that uses ultrasonic sensing technology for distance measurement, and temperature compensation is performed internally to improve the reliability of data.
Reference: DWM20072903
The Dragino LDDS20 is a LoRaWAN Ultrasonic liquid level sensor for Internet of Things solution.
Reference: DWM20030407
ESP8266 IOT Weather Station Kit with DHT11sensor UV sensor and water flow sensor IOT Weather Station Kit send the weather information with another ESP8266 module and display with an OLED kit.
Reference: DWM22091301
The TrackerD is built-in with GPS, Wi-Fi, BLE, Temperature, Humidity, Motion Detection, and Buzzer which can use Arduino IDE to customize the software for IoT solution.
Reference: DWM23060101
The D20-LB is a LoRaWAN Temperature Sensor for an Internet of Things solution. D20S-LB is designed for use in Soil or Road. D20-LB/ D20S-LB will convert the Temperature reading to LoRaWAN wireless data and send it to the IoT platform via the LoRaWAN gateway.
Reference: DWM21051606
The LTC2 Industrial LoRaWAN PT100 Temperature Transmitter Sensor Nodes base on LSN50-V2. It use to supports to read PT100 probe and convert the value to temperature and uplink to IoT server.
Reference: DWM21051607
The Dragino RS485-BL is an RS485 / UART to LoRaWAN Converter. It converts the RS-485 and UART devices into a LoRaWAN wireless network, simplifying the IoT installation and reducing the installation/maintenance cost.
Reference: DWM20022603
LT-22222-L is the Dragino LT series I/O Modules, are Long Range LoRa I/O Controller designed to simplify the installation of I/O monitoring.
Reference: DWM18011702
RAK811 Development Kit WisDuo LoRa Module is a combination of the RAK811 chipset and the RAK811 Breakout Board.
Reference: DWM16112801
DWM-LoRa1276F30 is a 500W high power wireless transceiver module, which integrates SemtechRF transceiver chip SX1276. There are 868MHz and 915MHz for avaialble options.
Reference: DWM18110801
Build your own LoRaWAN "The Things Network" packet-forwarding gateway on Windows 10 IoT Core in native .NET code.
Reference: DWM20060102
Brand: Semtech
DWM-RAK4200 Breakout Module is specifically designed to allow easy excess to the pins on the module in order to simplify development and testing.it's utilized is of an Xbee form factor.
Reference: DWM22090703
The SenseCAP S2100 Data Logger connects the sensor, collects the Data, and uploads it to the LoRaWAN gateway. It can support up to 100+ industrial sensors and 100+ grove sensors including various sensor types such as Analog/RS485/GPIO.
Reference: DWM22110601
The CPN01 is an NB-IoT Dry Contact Sensor. It detects open/close status and uplinks the info to IoT server via NB-IoT network. User can see the dry contact status, open time, and open counts in the IoT Server.
LoRa32u4 RA02 is a light and low consumption board based on the Atmega32u4 and SX1278 433MHz LoRA module.
