- On sale!
Reference: DWM14042301
Spring antenna is specialized for wireless data transmission. This antenna with good performance of V.S.W.R, small size design, easily installation, stable performance and good anti-shock and anti-aged compatible for Hoperf Modules.
Reference: DWM14032902
SMA rf antenna connector is pallets copper gold andexternal thread needle sma pallets plate rf connector.
Reference: DWM14032102
Whip antenna for sub-1 GHz, 433MHz,868MHz and 915MHz with SMA male connectors.it's used with wireless module recommanded by Hoperf .
Reference: DWM14042401
SMA RG178 extension female cable for GPS, GSM antenna,RF module, SMA cable,IPEX to SMA jumper cable.
Reference: DWM18032302
USD3.0/pcs MOQ100pcs LoRa Antenna designed for Lora application which required for outdoor waterproof highgain and work at ISM free band like 433MHz /868MHz /915MHz SMA Male Whip antenna.
Reference: DWM16121503
DWM-TLB-3.0QB SUB-1GHz / 2.4GHz Whip antenna with a Collapsible SMA male connectors.Which are available for 433MHz,868MHz.915MHz and 2.4GHz..
Reference: DWM17111002
LoRa Antenna-433MHz High Gain internal aerial piamater FPC Antenna with IPEX connctor.
Reference: DWM15101001
Brand: Semtech
RFM50 module series’ design is based on the high performance RF50 SoC chip, It include a CIP-51 core‘ MCU and 100mW transceiver. It operate at 433/470/868/915 MHz ISM band, comply with FCC, ETSI regulation.
The LDDS75 LoRaWAN Distance Detection Sensor node is a distance detection sensor that uses ultrasonic sensing technology for distance measurement, and temperature compensation is performed internally to improve the reliability of data.
The LDDS75 is a LoRaWAN Distance Detection Sensor for Internet of Things solution. It is used to measure the distance between the sensor and a flat object. The distance detection sensor is a module that uses ultrasonic sensing technology for distance measurement, and temperature compensation is performed internally to improve the reliability of data.
The LDDS75 can be applied to scenarios such as horizontal distance measurement, liquid level measurement, parking management system, object proximity and presence detection, intelligent trash can management system, robot obstacle avoidance, automatic control, sewer, bottom water level monitoring, etc.
It detects the distance between the measured object and the sensor, and uploads the value via wireless to LoRaWAN IoT Server.
The LoRa wireless technology used in LDDS75 allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
LDDS75 is powered by 4000mA Li-SOCI2 battery; It is designed for long term use up to 10 years*.
Each LDDS75 pre-loads with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect if there is network coverage, after power on.
LoRaWAN 1.0.3 Class A
Ultro low power consumption
Distance Detection by Ultrasonic technology
Flat object range 280mm - 7500mm
Cable Length : 25cm
Temperature Compensation
Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
AT Commands to change parameters
Uplink on periodically
Downlink to change configure
IP66 Waterproof Enclosure
4000mAh Battery for long term use
Horizontal distance measurement
Liquid level measurement
Parking management system
Object proximity and presence detection
Intelligent trash can management system
Robot obstacle avoidance
Automatic control, sewer
Bottom water level monitoring
1 x LDDS75
Dimensions and Weight:
Package Dimension: 150*120*55mm
Weight : 220g
XX: the default frequency band
EU433: Default frequency band EU433
CN470: Default frequency band CN470
EU868: Default frequency band EU868
IN865: Default frequency band IN865
KR920: Default frequency band KR920
AS923: Default frequency band AS923
AU915: Default frequency band AU915
US915: Default frequency band US915
Reference: DWM18110501
LG308 8 Channels Indoor LoRaWAN Pico Gateway is an open source LoRaWAN Pico Gateway. It lets you bridge LoRa wireless network to an IP network via WiFi, Ethernet, 4G cellular.
Reference: DWM19090402
The LPS8 is an open source LoRaWAN Gateway Build in SX1308 and SX1257 LoRa Tranceiver which provide 10 programmable parallel demodulation paths.
Reference: DWM20022601
LSN50-V2 Waterproof Long Range Wireless LoRa Sensor Node with external antenna,It is designed for outdoor use and powered by Li/SOCl2 battery for long term use.
Reference: DWM20061503
The LDS01 is a LoRaWAN Door Sensor. It detects door open/close status and will send periodically data every day as well as for each door open/close action. It also count the door open times and calculate last door open duration.
Reference: DWM19121101
ATmega328P LoRa Radio Node is based on SX1276/SX1278 which use the Arduino pro mini 8Mhz 3.3V bootloader, usage same as the Arduino pro mini.
Reference: DWM19062701
Yun Shield v1.1.6 runs Open Source OpenWrt system solve the Internet connectivity and storage issue for Arduino Board.
Reference: DWM20033101
ER18505+SPC1520 Super Pulse Cap 4000mAh Li/SOCI2 unchargable battery for LSN50 Sensor nodes.
Reference: DWM22051601
The DLOS8N /DLOS8N-EC25 Outdoor LoRaWAN Gateway includes 1pcs SX1302 and 2pcs SX1250 LoRa Tranceiver which provide 10 programmable parallel demodulation paths.
Reference: DWM18110902
Getting started with LoRaWAN for Cypress PSoC 6 MCU based on LMiC to access to LoRaWAN TTN (The Things Network) using Dragino LoRa gateway, RFM95W.
Reference: DWM25022801
The DDS04-LS is a Solar-powered LoRaWAN 4-Channels Distance Sensor that can be applied to scenarios such as horizontal distance measurement, parking management system, object proximity and presence detection, intelligent trash can management system, robot obstacle avoidance, automatic control, sewer, etc.
Reference: DWM23122601
SDI-12-NB is an SDI-12 to NB-IoT Converter that supports BLE configuration and OTA update and is designed for Smart Agriculture sensors and Weather Station.
Reference: DWM25070201
The SE0X-LS is a Solar-Powered LoRaWAN saline-alkali soil and loamy soil Sensor. It detects Soil Moisture, Soil Temperature, and Soil Conductivity, and uploads the value via wireless to the LoRaWAN IoT Server.
Reference: DWM25102205
The BH01-LB BLE to LoRaWAN Hub is an edge communication node device designed for cold chain warehouse monitoring, smart agricultural environment monitoring, asset tracking and urban infrastructure health management.
Reference: DWM25102401
The DR-THP-6P integrated temperature/humidity/air pressure detection which work with the WSC2-Compact-LS LoRaWAN Weather Station Kit.
Reference: DWM23061502
The Dragino PS-LB-T or PS-LB-I sensors are LoRaWAN Pressure Sensor for Internet of Things solution. PS-LB can measure Air, Water pressure and liquid level and upload the sensor data via wireless to LoRaWAN IoT server.
Reference: DWM22071401
The LPS8v2 is an open-source Debian system LoRaWAN Gateway. It lets you bridge LoRa wireless network to an IP network via WiFi , Ethernet and also with 4G Cellular Network capability.
Reference: DWM25030201
PS-NB-D NB-IoT Differential Pressure Sensor uses Differential Pressure Sensor includes various models to cover NB-IoT wireless transmission and different ranges of pressure measurements.
Reference: DWM22072101
LA66 LoRaWAN Shield is the Arduino shield base on LA66. Users can use LA66 LoRaWAN Shield to rapidly add LoRaWAN or peer-to-peer LoRa wireless function to Arduino projects.
Reference: DWM22100802
AN-102D LoRaWAN smoke detector sensor node with high-precision, the device emits red light when it detects a fire alarm. The device sends alarm data to the platform to remind relevant personnel on the site to deal solve it.
Reference: DWM21051603
The LSNPK01 is a LoRaWAN Soil NPK Sensor for IoT of Agriculturebase. detects soil's Nitrogen, Phosphorus, and Potassium use TDR method, and uploads these values via wireless to LoRaWAN IoT Server.
The LDDS75 LoRaWAN Distance Detection Sensor node is a distance detection sensor that uses ultrasonic sensing technology for distance measurement, and temperature compensation is performed internally to improve the reliability of data.