- On sale!

Reference: DWM14042301
Spring antenna is specialized for wireless data transmission. This antenna with good performance of V.S.W.R, small size design, easily installation, stable performance and good anti-shock and anti-aged compatible for Hoperf Modules.
Reference: DWM14032902
SMA rf antenna connector is pallets copper gold andexternal thread needle sma pallets plate rf connector.
Reference: DWM14032102
Whip antenna for sub-1 GHz, 433MHz,868MHz and 915MHz with SMA male connectors.it's used with wireless module recommanded by Hoperf .
Reference: DWM14042401
SMA RG178 extension female cable for GPS, GSM antenna,RF module, SMA cable,IPEX to SMA jumper cable.
Reference: DWM18032302
USD3.0/pcs MOQ100pcs LoRa Antenna designed for Lora application which required for outdoor waterproof highgain and work at ISM free band like 433MHz /868MHz /915MHz SMA Male Whip antenna.
Reference: DWM16121503
DWM-TLB-3.0QB SUB-1GHz / 2.4GHz Whip antenna with a Collapsible SMA male connectors.Which are available for 433MHz,868MHz.915MHz and 2.4GHz..
Reference: DWM17111002
LoRa Antenna-433MHz High Gain internal aerial piamater FPC Antenna with IPEX connctor.
Reference: DWM15101001
Brand: Semtech
RFM50 module series’ design is based on the high performance RF50 SoC chip, It include a CIP-51 core‘ MCU and 100mW transceiver. It operate at 433/470/868/915 MHz ISM band, comply with FCC, ETSI regulation.
RAK811 WisNode LoRa Module development board is compatible with Arduino Development Board. It can also be used as an extension board development with Arduino.
WisNode-LoRa RAK811 /RAK812 LoRa Arduino shield Support AS923, 868/915MHz, LoRa/TTN, Open source LoRa development board.
The following image is RAK WisNode-Lora development board,and it compatible Arduino development board, It also can be used as an extension board development with Arduino. The interface resource are as follow:
Function | Name | Description |
---|---|---|
Module | U3 | RAK811 Lora module |
External Interface | Micro USB | Power Supply; DC 5V Input,USB to TTL communication interface |
Key | Reset | Module Reset Key |
Leading Foot | P1 | Boot Switch Pin,When Boot Pin Switch to 3.3V Module will into the Boot Mode |
P4 | Debug Pin | |
P5 | Uart Switch Pin | |
Power Test | J1 | Module Power Test Pin |
LED Indicator | LED1(Power) | Power Indicator Light |
Connect the evaluation board to the computer via the Micro USB line, Through the computer serial port tool to send commands to the module.As shown in the following figure:
at+mode=0 /* SET LoraWAN work mode */ OK at+get_config=dev_eui /* GET Dev_EUI check */ OK3037343644357402 at+set_config=app_eui:39d7119f920f7952&app_key:a6b08140dae1d795ebfa5a6dee1f4dbd /* SET LoraGateway app_eui and app_key , big endian*/ OK at+join=otaa /* Join OTAA type*/ OK at+recv=3,0,0 /* Join status success*/
Welcome to RAK811 at+mode=0 /* SET LoraWAN work mode */ OK at+set_config=dev_addr:00112233&nwks_key:3432567afde4525e7890cfea234a5821& apps_key:a48adfc393a0de458319236537a11d90 /* SET LoraGateway dev_addr nwks_key and apps_key , big endian*/ OK at+join=abp /* Join ABP type*/ OK
/*After join gateway success, then can send and receive data*/ at+send=0,2,000000000000007F0000000000000000 /*APP port:2, battery level 50%, unconfirmed message*/ at+recv=2,0,0 /*unconfirmed mean tx success*/ at+send=1,2,000000000000007F0000000000000000 /*APP port :2, battery level 50%, confirmed message*/ at+recv=1,0,0 /*confirmed mean receive ack from gateway*/ /*If gateway has data to send module, will receive date meanwhile ack */ at+recv=0,2,10,30313233343536373839 /*APP port :2, receive size 10, hex:30313233343536373839*/
/* Module A Rx Side*/ Welcome to RAK811 at+mode=1 /* SET LoraP2P work mode */ OK at+rf_config=867700000,10,0,1,8,14 /* SET LoraP2P Frequency:867.7MHz, SF10,Bandwith 125KHz, coding Rate:4/5, Preamlen:8, tx power:14dbm */ OK at+rxc=1 /* SET LoraP2P Rx continue enable report rx data */ OK at+rx_stop /* If want stop Rx continue */
/* Module B Tx Side*/ Welcome to RAK811 at+mode=1 /* SET LoraP2P work mode */ OK at+rf_config=867700000,10,0,1,8,14 /* SET LoraP2P Frequency:867.7MHz, SF10,Bandwith 125KHz, coding Rate:4/5, Preamlen:8, tx power:14dbm */ OK at+txc=100,1000,800100000600010002da9557e142d9 /* SET LoraP2P Tx continue ,100 packets, 1S interval, hex data */ OK at+recv=9,0,0 /*When Tx complete */ at+tx_stop /* If want stop Tx continue */
To upgrade the Lora module, First we should make the module get into Boot mode. We should switch the P1 pin make the Boot pin connection with 3.3V Pin. Then reset the module, Operate according to the steps:
1.Open the Flash Loader Demonstrator tool,Set the serial port parameters;
2.Click the “NEXT” button, arrive the following interface;
3.The again the “Next” button,Choose STM32L1_Cat2-128K;
4.Choose “Download to device”,Set the path to the new firmware, and click “NEXT” button;
5.Upgrading;
6.Upgrade Successful.
Reference: DWM17102702
LoRa Antenna designed for Lora application which required for outdoor waterproof highgain and work at ISM free band like 433MHz /868MHz /915MHz SMA Male Whip antenna.
Reference: DWM18011701
RAK811 LoRa module complies with the latest LoRaWAN Class A & C protocol specifications, it is simple to access LWPA IOT platforms integrates SX1276 and stm32L with TELEC CE FCC KCC certification.
Reference: DWM18011801
DWM-RAK83 433MHz/ 868MHz/ 915MHz SX1301 LoRa/ LoRaWAN Gateway Module combine a host system like Raspberry Pi or WisAP(OpenWRT based) or WisCam to help you realize the whole Lora system development.
Reference: DWM23091101
The BG96 is an LTE Cat M1/Cat NB1/EGPRS module which is compatible with Quectel’s LTE Standard module EG91/EG95, LPWA module BC95-G/BG95, UMTS/HSPA module UG95/UG96 and GSM/GPRS module M95.
Reference: DWM19091701
DWM-RAK2245 SX1301 8 Channels Stamp Edition is a LoRaWAN gateway Module based on SX1301,Pre-install LoRa gatewayOS.
Reference: DWM20052801
The DWM-RAK7204 is an LPWAN node that serves as an environmental monitoring station. The high-precision sensors, can measure changes in temperature, humidity, gas pressure and provide an indoor air quality index.
Reference: DWM19091602
DWM-RAK7243 Pilot LoRas Gateway Pro Kit with GPS modules for PoC Raspberry Pi 3B+, RAK2245 Pi HAT.
Reference: DWM22062302
This Kit consists of a Sensor Node to measures air temperature, air humidity, barometric pressure, and environment luminosity values. Transmitting data periodically to a LoRaWan® server.
Reference: DWM22061601
RAK10700 is a GNSS Tracker device with a GNSS modem providing LPWAN and BLE communication using the nRF52 MCU and SX1262 LoRa transceiver of the RAK4631 Core module.
Reference: DWM20053101
Brand: Semtech
DWM-RAK4200 LPWAN Module includes an STM32L071 MCU and an SX1276 LoRa® chip. It has an ultra-low power consumption of 1.5uA in sleep mode and high LoRa® output power up to 19dBm max in work mode.
Reference: DWM20053103
Brand: Semtech
The DWM-RAK4600 development board allows access to all serial and GPIO ports for easy configuration. The RAK4600 core module includes nRF52832 MCU and SX1276 LoRa® chip to help you quickly and easily develop/test your firmware.
Reference: DWM19091601
RAK7205 LoRa Tracker built on RAK5205 integrated the Ublox Max 7Q module built on SX1276 LoRaWAN modem with low power micro-controller STM32L1.
Reference: DWM21030102
LoRa Antenna-868MHz /915MHz 8dBi Glass Fiber Antenna with N Female Connector. Out Door Waterproof Fiberglass Antenna which is designed for Lora application required for high gain outdoor waterproof.
Reference: DWM19070805
RAK7205 LoRa Tracker With Solar Panel built on RAK5205 integrated the Ublox Max 7Q module built on SX1276 LoRaWAN modem with low power micro-controller STM32L1.
Reference: DWM20092101
DWM-RAK7240 8 channels OpenWRT OS DIY Enterprise LoRa Gateway Builtin OpenWRT OS support 8 channels LoRa/4G/WIFI/GPS .
Reference: DWM18011801
DWM-RAK83 433MHz/ 868MHz/ 915MHz SX1301 LoRa/ LoRaWAN Gateway Module combine a host system like Raspberry Pi or WisAP(OpenWRT based) or WisCam to help you realize the whole Lora system development.
Reference: DWM19070801
LoRa Antenna-433MHz /470MHz /868MHz /915MHz 5.8dBi Glass Fiber Antenna with N Female Connector. Out Door Waterproof Fiberglass Antenna which is designed for Lora application required for high gain outdoor waterproof.
Reference: DWM20053001
Brand: Semtech
The DWM-RAK4260 LPWAN Module is based on Microchip’s ATSAMR34J18B integrating a 32-bit ARM Cortex -M0+ MCU with a LoRa Transceive, provides a number of highly configurable peripherals (configurable as I2C/SPI/UART interfaces).
Reference: DWM19070804
RAK7258 Micro Gateway is a full 8-channel LoRa Gateway with built-in Ethernet connectivity for a straightforward setup. Additionally, there is an onboard Wi-Fi setup that allows it to be easily configured via the default Wi-Fi AP mode.
RAK811 WisNode LoRa Module development board is compatible with Arduino Development Board. It can also be used as an extension board development with Arduino.