All best sellers
  • On sale!

GPS02-UBX Quad-mode satellite UBLOX GPS module adopts u-blox M10

DWM23082003

GPS02-UBX GPS module features the u-blox M10 standard precision GNSS platform and provides exceptional sensitivity and acquisition times for all L1 GNSS signals Supports concurrent reception of up to four GNSS (GPS, GLONASS, Galileo, and BDS)

Connector
$8.50
Tax excluded
Quantity

Description

GPS02-UBX GPS module features the u-blox M10 standard precision GNSS platform and provides exceptional sensitivity and acquisition times for all L1 GNSS signals. The extremely low power consumption in continuous tracking mode allows great power autonomy for all battery-operated devices, such as asset trackers, without compromising on GNSS performance.

GPS02-UBX module supports concurrent reception of up to four GNSS (GPS, GLONASS, Galileo, and BDS). Note: Choose three of four, BDS and GLONASS cannot be used at the same time.

The high number of visible satellites enables the receiver to select the best signals.

This maximizes the position accuracy, in particular under challenging conditions such as in deep urban canyons. In the firmware described here,however, the number of concurrently received GNSS is limited to three. u-blox Super-S (Super-Signal) technology offers great RF sensitivity.

It provides high sensitivity, high positioning accuracy, low power consumption and low cost positioning and navigation solutions for the manufacture of navigation and positioning terminal products such as vehicle, ship borne, handheld and wearable.

Features 

Support BDS B1I, GPS L1C/A,GLO L1OF, Gal E1-B/C frequency point

Support BDS/GPS/GLONASS/Galileo single-mode,dual-mode and multi-mode work, can switch between each other by command, default BDS/GPS/GLO tri-mode work

Support power supply to active antenna

With backup power input interface

Support hot start

Support external reset

Support UART and I2C interface

Cold start capture sensitivity up to -148dBm. Tracking sensitivity up to -166 dBm.

Support A-GNSS assisted positioning

Applications

Personal positioning and navigation products

Vehicle, ship positioning and navigation

Internet of Things

Handheld portable device

Order Info:

The Connector with NONE is the GPS02-UBX module.

The Connector with the IPEX is the start kit with the GPS02-UBX module with IPEX as the Antenna connector.

The Connector with the SMA is the start kit with the GPS02-UBX module with SMA as the Antenna connector.

Parameters

Parameter Description Minimum Typical Maximum Unit Condition
Operating conditions
Operating voltage range VCC 2.7 3.3 3.6 V  
V_BCKP 2.5 3.3 3.5 V  
Temperature range Working -40   85  
Storage -40   125  
Current consumption
Receive current     < 25   mA @Dual mode,VCC=3.3V, V_BCKP=3.3V
Sleep current     < 35   uA VCC=0V, V_BCKP=3.3V
Radio frequency parameters
Positioning accuracy Level   < 3   m @Open land
Elevation   < 4.5   m
Speed Measurement accuracy     <0.1   m  
Sensitivity capture   -148   dBm  
track   -166   dBm  
External antenna gain       30 dB  
Speed measurement accuracy     < 0.1   m/s  
Time to First fix(TTFF) Cold start   < 28   s  
Hot Start   1   s  
Recapture   1   s  
Serial port parameters
Serial  baud rate   4800 38400 921600 bps  
Data update rate (Single mode) BDS/GPS/ GLONASS/ Galileo   1 18 Hz Default 1 Hz
Data update rate (Dual mode) BDS+GPS   1 10 Hz
BDS+Galileo   1 10 Hz
GPS+GLONASS   1 10 Hz
GPS+Galileo   1 10 Hz
GLONASS+Galileo   1 10 Hz
Data update rate (Tri-mode) GPS+Galileo+GLONASS   1 10 Hz
GPS+Galileo+BDS   1 10 Hz

Pin Definition:(Pin assignment see the picture)

Pin number Pin definition I/O Level standard Description
1、3、10 GND   Power ground
2 ANT I   Antenna Input
4、6、9 NC   No function
5 VCC_RF O VCC 3.3V output, powered for the antenna or LNA, not exceed 20mA
7 SDA I/O 0-3.5 V I2C interface
8 SCL I 0-3.5 V I2C interface 
11 TXD O 0-3.5 V Serial interface
12 RXD I 0-3.5 V Serial interface
13 1PPS O 0-3.5 V 1 pulse output per second
14 PIO5 I 0-3.5 V Reserved interface
15 V_BACK I 2.5-3.5 V Backup power input
16 VCC 3.0-3.5 V Main power input
17 VCC_IO 3.0-3.5 V IO power input
18 RESET I 0-3.5 V External reset, active low. Cannot be connected to ground through capacitor

Useful Link:

Datasheet for the GPS02-UBX Module

User Manual of the GPS02-UBX module start kit

Product Details
DWM23082003
100 Items
You might also like
9 other products in the same category:

Reviews

Write your review

GPS02-UBX Quad-mode satellite UBLOX GPS module adopts u-blox M10

GPS02-UBX GPS module features the u-blox M10 standard precision GNSS platform and provides exceptional sensitivity and acquisition times for all L1 GNSS signals Supports concurrent reception of up to four GNSS (GPS, GLONASS, Galileo, and BDS)

Write your review

Follow us on Facebook