Reference: DWM15011202

Brand: Semtech

RFM68W-S2 Low cost 433MHz /868MHz /915MHz HopeRF ISM FSK Transimitter rf module

Review(s): 0

The RFM68W is an ultra-low-cost, fully integrated FSK or OOK transmitter suitable for operation between 310 and 450 MHz, 860 and 870 MHz, as well as 902 and 928 MHz..The RFM68W offers integrated radio performance with cost efficiency and is suited for operation in North America FCC part 15.231, FCC part 15.247 DTS and FHSS modes, 15.249, and Europe EN 300...

Price $2.50
More
In stock

Reference: DWM15101101

E931.96 Ultra-Low Power PIR Controller

Review(s): 0

The E931.96 is an ultra-low power motion detector controller integrated circuit. The device is ideally suited for battery operated wireless motion sensors that make use of an MCU for handling com munication.

Price $1.80
More
In stock
All best sellers
HopeRF CMOSTEK USB Programmer
  • HopeRF CMOSTEK USB Programmer

HopeRF CMOSTEK USB Programmer

DWM15081901
Rating 

The USB Programmer is the configuration interface for the user to program the configuration to CMOSTEK RF procducts with the RFPDK. It connects the module containing RF products via EM-Connector and connects the PC via USB cable. 3 LEDs are available to indicate the working status of the USB programmer.

$49.90
Quantity

  • Security policy (edit with Customer reassurance module) Security policy (edit with Customer reassurance module)
  • Delivery policy (edit with Customer reassurance module) Delivery policy (edit with Customer reassurance module)
  • Return policy (edit with Customer reassurance module) Return policy (edit with Customer reassurance module)
Description

    The USB Programmer is the configuration interface for the user to program the configuration to CMOSTEK RF products with the RFPDK. It connects the module containing RF products via EM-Connector and connects the PC via USB cable. 3 LEDs are available to indicate the working status of the USB programmer.


CMTRFPDK programer

Definition of EM-Connector

 PIN Number Signal name PIN Number Signal name
 1  TE  2  GND
3  SCL2_O  4  VDD_3.3V
 5  CLK  6  RSTB2_O
 7  DATA  8  SAD2
 9  RSTB1_O  10  BURN


Definition of LEDs

NameDescriptions Color
Run
Will flash when there is data communication (not  burning),
Will be on when buring the CMT2110A-EM
 Green
Err  Will be on for 5 seconds when the burning is failed  Red
USB  Will be on when the USB is correctly connected to the PC  Green


Useful Link:  PC (RFPDK V1.33)


RFPDK (RF Products Development Kit) is a member of all Development Kits supporting

the development and manufacturing with CMOSTEK NextGenRFTM products.

It is a PC application runs on Windows 2000, XP, 7 and 8.

It works with the USB Programmer to configure the CMOSTEK NextGenRFTM products.


Once the program has started, the device selection panel of the RFPDK appears.
The user can use the two tabs at the top of the panel to choose the product family:
either devices operating in the 2.4 GHz frequency band or the sub-1 GHz frequency band.
Under each tab, all the products belong to the family are listed in the middle of the panel.
The products can be filtered by the buttons of All, Transmitters, Receivers and Transceivers.
The main features of the products, including Device, Function, Band, Package, Modem and
Symbol Rate, are shown to assist the device selection.
 
If an evaluation module is connected to the PC through the USB Programmer,
the device part number, USB Programmer hardware version and firmware revision
will appear in the “List of connected device”.
 
                                             


When the device, the USB Programmer and the PC (RFPDK) are properly connected,

the Read Device function can be used to read out and upload the EEPROM contents

from the device to the PC. The user can use this function by selecting Operation à Read Device.

After that, a Save-as window pops out so that the user can save the read-out contents into a

text file suffixed by “.exp”.



Product Details
DWM15081901
33 Items
Reviews

Write your review

HopeRF CMOSTEK USB Programmer

HopeRF CMOSTEK USB Programmer

The USB Programmer is the configuration interface for the user to program the configuration to CMOSTEK RF procducts with the RFPDK. It connects the module containing RF products via EM-Connector and connects the PC via USB cable. 3 LEDs are available to indicate the working status of the USB programmer.

Write your review
You might also like
16 other products in the same category:

Reference: DWM15011303

RFM65W-S2 433MHz /868MHz /915MHz HopeRF Receiver rf module

Review(s): 0

The RFM65W is a highly integrated RF receiver capable of operation over a wide frequency range, including the 433MHz,868MHz and 915 MHz license-free ISM (Industry Scientific and Medical) frequency bands.TrueRF™ technology enables a lowcost external component count (elimination of the SAW filter) whilst still satisfying ETSI and FCC regulations.

Price $3.50
More
In stock

Follow us on Facebook