Все популярные товары
  • Banner

HopeRF CMOSTEK USB Programmer
  • HopeRF CMOSTEK USB Programmer

HopeRF CMOSTEK USB Programmer

DWM15081901

The USB Programmer is the configuration interface for the user to program the configuration to CMOSTEK RF procducts with the RFPDK. It connects the module containing RF products via EM-Connector and connects the PC via USB cable. 3 LEDs are available to indicate the working status of the USB programmer.

99,00 $
Без НДС
Количество

Описание

    The USB Programmer is the configuration interface for the user to program the configuration to CMOSTEK RF products with the RFPDK. It connects the module containing RF products via EM-Connector and connects the PC via USB cable. 3 LEDs are available to indicate the working status of the USB programmer.

 

CMTRFPDK programer

Definition of EM-Connector

 PIN Number  Signal name  PIN Number  Signal name
 1  TE  2  GND
3  SCL2_O  4  VDD_3.3V
 5  CLK  6  RSTB2_O
 7  DATA  8  SAD2
 9  RSTB1_O  10  BURN


Definition of LEDs

Name Descriptions  Color
Run
Will flash when there is data communication (not  burning),
Will be on when buring the CMT2110A-EM
 Green
Err  Will be on for 5 seconds when the burning is failed  Red
USB  Will be on when the USB is correctly connected to the PC  Green

 

Useful Link:  PC (RFPDK V1.33)

 

RFPDK (RF Products Development Kit) is a member of all Development Kits supporting

the development and manufacturing with CMOSTEK NextGenRFTM products.

It is a PC application runs on Windows 2000, XP, 7 and 8.

It works with the USB Programmer to configure the CMOSTEK NextGenRFTM products.


Once the program has started, the device selection panel of the RFPDK appears.
The user can use the two tabs at the top of the panel to choose the product family:
either devices operating in the 2.4 GHz frequency band or the sub-1 GHz frequency band.
Under each tab, all the products belong to the family are listed in the middle of the panel.
The products can be filtered by the buttons of All, Transmitters, Receivers and Transceivers.
The main features of the products, including Device, Function, Band, Package, Modem and
Symbol Rate, are shown to assist the device selection.
 
If an evaluation module is connected to the PC through the USB Programmer,
the device part number, USB Programmer hardware version and firmware revision
will appear in the “List of connected device”.
 
                                             


When the device, the USB Programmer and the PC (RFPDK) are properly connected,

the Read Device function can be used to read out and upload the EEPROM contents

from the device to the PC. The user can use this function by selecting Operation à Read Device.

After that, a Save-as window pops out so that the user can save the read-out contents into a

text file suffixed by “.exp”.

 

 

Подробнее о товаре
DWM15081901
28 штук
Возможно, вам понравится
В этой категории 16 товаров:

Код: DWM15011201

Бренд: Semtech

RFM68CW-S2 Small Size 433MHz /868MHz /915MHZ HopeRF transmitter RF module

The RFM68CW is an ultra-low-cost, FSK or OOK transmitter module suitable for operation in the  433, 868 and 915 MHz licence free ISM bands., the RFM68CW may be used without the requirement for configuration via an MCU. However, in conjunction with a microcontroller, the communication link parameters may be re-configured. Including, output power,...

Цена 2,50 $
Еще
По наличию

Reviews

Write your review

HopeRF CMOSTEK USB Programmer

The USB Programmer is the configuration interface for the user to program the configuration to CMOSTEK RF procducts with the RFPDK. It connects the module containing RF products via EM-Connector and connects the PC via USB cable. 3 LEDs are available to indicate the working status of the USB programmer.

Write your review

Присоединяйтесь к нам в Facebook