- New
![](https://dwmzone.com/4359-large_default/heltec-stick-lite-v3-support-meshtastic-based-wifi-esp32-s3-and-lora-sx1262.jpg)
Reference: DWM14042301
Spring antenna is specialized for wireless data transmission. This antenna with good performance of V.S.W.R, small size design, easily installation, stable performance and good anti-shock and anti-aged compatible for Hoperf Modules.
Reference: DWM14032902
SMA rf antenna connector is pallets copper gold andexternal thread needle sma pallets plate rf connector.
Reference: DWM14032102
Whip antenna for sub-1 GHz, 433MHz,868MHz and 915MHz with SMA male connectors.it's used with wireless module recommanded by Hoperf .
Reference: DWM14042401
SMA RG178 extension female cable for GPS, GSM antenna,RF module, SMA cable,IPEX to SMA jumper cable.
Reference: DWM18032302
USD3.0/pcs MOQ100pcs LoRa Antenna designed for Lora application which required for outdoor waterproof highgain and work at ISM free band like 433MHz /868MHz /915MHz SMA Male Whip antenna.
Reference: DWM16121503
DWM-TLB-3.0QB SUB-1GHz / 2.4GHz Whip antenna with a Collapsible SMA male connectors.Which are available for 433MHz,868MHz.915MHz and 2.4GHz..
Reference: DWM17111002
LoRa Antenna-433MHz High Gain internal aerial piamater FPC Antenna with IPEX connctor.
Reference: DWM15101001
Brand: Semtech
RFM50 module series’ design is based on the high performance RF50 SoC chip, It include a CIP-51 core‘ MCU and 100mW transceiver. It operate at 433/470/868/915 MHz ISM band, comply with FCC, ETSI regulation.
HELTEC Stick Lite V3 can install the Meshtastic firmware as a development board which is a highly integrated product based on ESP32(including WiFI and BLE), Li-Po battery management system.
HELTEC Stick Lite V3 can install the Meshtastic firmware as a development board which is a highly integrated product based on ESP32(including WiFI and BLE), Li-Po battery management system.
Microprocessor: ESP32-S3FN8 (Xtensa® 32-bit LX7 dual core processor, five stage pipeline rack Structure, main frequency up to 240MHz).
Semtech SX1262
Frequency Options:
433 - 510 MHz
470 - 510 MHz
863 - 870 MHz
902 - 928 MHz
USB-C
Dedicated 2.4 GHz stamped metal antenna for WiFi/Bluetooth
U.FL/IPEX antenna connector for LoRa (next to the V3 icon)
No display.
User and Reset Buttons
Additional GPIO availability
No GPS
SDA: GPIO41
SCL: GPIO42
Onboard SH1.25-2 battery interface, integrated lithium battery management system (charge and discharge management, overcharge protection, battery power detection, USB / battery power automatic switching).
Integrated WiFi, LoRa, Bluetooth three network connections, onboard Wi-Fi, Bluetooth dedicated 2.4GHz metal spring antenna, reserved IPEX (U.FL) interface for LoRa
Integrated CP2102 USB to serial port chip, convenient for program downloading, debugging information printing.
Support the Arduino development environment;
Parameters | Description |
---|---|
Master Chip | ESP32-S3FN8 (Xtensa®32-bit lx7 dual core processor) |
LoRa Chipset | SX1262 |
USB to Serial Chip | CP2102 |
Frequency | 470~510MHz, 863~928MHz |
Max. TX Power | 21d B ± 1d B |
Max. Receiving sensitivity | -134dBm |
Wi-Fi | 802.11 b/g/n, up to 150Mbps |
Bluetooth LE | Bluetooth 5, Bluetooth mesh |
Hardware Resource | 7*ADC1 + 9*ADC2; 8*Touch; 3*UART; 2*I2C; 2*SPI; etc. |
Memory | 384KB ROM; 512KB SRAM; 16KB RTC SRAM; 8MB SiP Flash |
Battery | 3.7V lithium battery power supply and charging |
Operating temperature | -20 ~ 70 ℃ |
Dimensions | 58.08 * 22.6* 8.2 mm |
Interface | Type-C USB; 2*1.25 lithium battery interface; LoRa ANT(IPEX1.0); 2.4G ANT(IPEX1.0); 2*20*2.54 Header Pin |
x1 - Heltec Wireless Stick Lite(V3) Pre-flashed with Meshtastic
x1 - SMA Male Glue Rod Antenna
x1 - IPEX to SMA Female Pigtail
x1 - SH1.25×2 Battery Connector
x2 - Pin Headers
Heltec ESP(ESP32&ESP8266) framework
Reference: DWM22090701
TTGO Meshtastic T-Beam V1.1 ESP32 LoRa Development Board 433MHz 868MHz 915MHz 923MHz with WiFi Bluetooth GPS and 0.96 OLED Display.
Reference: DWM23010502
HTIT-Wsh ESP32-S3 SX1262 WIFI BLE LoRa/ LoRaWAN Wireless Shell-V3 provides Wi-Fi, BLE, and LoRa solutions, which perfectly support Arduino development environment.
Reference: DWM24012601
The Meshtastic starter Kit includes a WisBlock Base board and the RAK4631 WisBlock Core module, already flashed with the Meshtastic firmware. Power the boards up and start sending messages immediately.
Reference: DWM24061701
HELTEC LoRa32 V3.1 can install the Meshtastic firmware as a development board which is a highly integrated product based on ESP32(including WiFI and BLE), Li-Po battery management system,0.96” OLED also included.
Reference: DWM20101101
DWM-HT-M00 dual-channel LoRaWAN gateway Drive SX1276 chip by ESP32 low-cost , with Type-C interface.
Reference: DWM22022801
HT-M2808 HNT Miner Helium Full Hotspot is as an efficient miner for a new cryptocurrency, Helium (HNT) which can provides a WiFi configuration interface via the device's BLE services.
Reference: DWM22051404
LoRaWAN Helium HNT miner Indoor networking antenna available with 433MHz,868MHz and 915MHz.
Reference: DWM20101002
DWM-HTCC-AC01 is based on ASR6501 and SX1262 support Arduino®, can run the LoRaWAN 1.0.3 protocol can easily connect batteries and solar panels sensor node.
Reference: DWM22092703
he ATECC608B is a secure element from the Microchip CryptoAuthenticationTM portfolio with advanced Elliptic Curve Cryptography (ECC) capabilities.
Reference: DWM23010503
ESP32-LoRa Dev Backplane Compatible with HTIT-Wsh and HT-CT62.
Reference: DWM22123004
WiFi LoRa 32 is a classic IoT dev-board designed & produced by Heltec Automation. The newly launched V3 version has the same pin sequence as the V2 version and retains Wi-Fi, BLE, LoRa, OLED display, and other functions.
Reference: DWM20111002
DWM-HTCC-1/2AA is based on ASR6502 and SX1262 support Arduino®, can run the LoRaWAN 1.0.2 protocol can easily connect batteries end sensor node.
Reference: DWM23010501
HT-CT62 is a Low cost WIFI LoRa/ LoRaWAN module for long range wireless communication for smart cities, smart farms, smart homes, and IoT makers. Support the Arduino development environment.
Reference: DWM20101001
DWM-HTCC-AC02 is based on ASR6501 and SX1262 support Arduino®, can run the LoRaWAN 1.0.2 protocol can easily connect batteries and solar panels sensor node.
Reference: DWM23010502
HTIT-Wsh ESP32-S3 SX1262 WIFI BLE LoRa/ LoRaWAN Wireless Shell-V3 provides Wi-Fi, BLE, and LoRa solutions, which perfectly support Arduino development environment.
Reference: DWM20101301
DWM-HT-M01 SX1308 Baseband Mini LoRaWAN gateway support both SPI and USB interface can work with Windows® (7, 8, 10 or higher) or Linux (Raspberry Pi®).
Reference: DWM24061701
HELTEC LoRa32 V3.1 can install the Meshtastic firmware as a development board which is a highly integrated product based on ESP32(including WiFI and BLE), Li-Po battery management system,0.96” OLED also included.
Reference: DWM22123004
HT-M02 design strictly with industrial standards for the industrial environment, Integrated Linux Operating System (4.19 Kernel, Debian Stretch10).Support DC power supply and PoE power supply, support 4G(cat.1, cat.4),WiFi / Bluetooth,it is convenient for users to apply in different scenarios.
Reference: DWM24061801
HELTEC Wireless Tracker can install the Meshtastic firmware as a development board which is based on ESP32-S3FN8. It integrates both SX1262 and UC6580 to provide fast GNSS solution for IoT.
Reference: DWM23010504
ESP32-S3 SX1262 WIFI BLE LoRa/ LoRaWAN Wireless Stick-V3 provides Wi-Fi, BLE, and LoRa solutions, which perfectly support Arduino®。 Users can easily carry out secondary development and application.
HELTEC Stick Lite V3 can install the Meshtastic firmware as a development board which is a highly integrated product based on ESP32(including WiFI and BLE), Li-Po battery management system.