DWM-N503AS module based TI CC1101 transceiver, the module leads out all pins of CC1101 chip, The interface of the module is SPI port and RF pin. SMD package, small size, the module is suitable for SMT production. Rapid development without understanding RF. The module supports Ardunio and WMbus.
DWM-N503AS is suitable for ISM band in EU and USA.
Specifications
Protocols IEEE 802.15.4, Wireless M-Bus (T, S, C mode), 6LoWPAN, MIOTY
Frequency bands (MHz) 387-464,774-928
TX power (Max) (dBm) 12
RX current (lowest) (mA) 18
TX current (lowest) (mA) 35
Sleep current (lowest)(uA) 1
Peripherals SPI
Data rate (Max) (kbps) 500
Operating temperature range (C) -30 to 75
Package SMD
Size 16 x 15 x 3mm
Antenna Interface RF pin
DWM-N503AS Parameter
DWM-N503AS RF Interface
|
Parameter
|
Frequency
|
433M, 868M, 915MHz
|
Output Power
|
+12dBm
|
Sensitivity
|
-116dBm
|
Symbol Rate
|
0.6 to 500kbps
|
Deviation
|
+/-10kHz
|
Distance
|
500m
|
DWM-N503AS Hardware parameters
|
Value
|
Size
|
17 x 16 x 3mm
|
Antenna Interface
|
RF pin
|
Communication Interface
|
SPI
|
Package
|
SMD
|
DWM-N503AS Electrical Parameters
|
Minimum
|
Typical
|
Maximum
|
Volt
|
1.8V
|
3.3V
|
3.6V
|
Emission Current
|
|
35mA
|
|
Receiving Current
|
|
18mA
|
|
Sleep current
|
|
0.2uA
|
|
Working Temperature
|
-30℃
|
|
75℃
|
CC1101 Description
CC1101 is a low-cost sub-1 GHz transceiver designed for very low-power wireless applications. The circuit is mainly intended for the ISM (Industrial, Scientific and Medical) and SRD (Short Range Device) frequency bands at 315,433,868, and 915 MHz, but can easily be programmed for operation at other frequencies in the 300-348 MHz,387-464 MHz and 779-928 MHz bands.
The RF transceiver is integrated with a highly configurable baseband modem. The modem supports various modulation formats and has a configurable data rate up to 600 kbps.
CC1101 provides extensive hardware support for packet handling, data buffering, burst transmissions, clear channel assessment, link quality indication, and wake-on-radio.
The main operating parameters and the 64- byte transmit/receive FIFOs of CC1101 can be controlled via an SPI interface. In a typical system, the CC1101 will be used together with a microcontroller and a few additional passive components.
The CC1190 850-950 MHz range extender [21] can be used with CC1101 in long range applications for improved sensitivity and higher output power.
ISM Frequency supported by N503AS CC1101 module
433M band: 433MHz to 435 MHz (China, EU)
770M band:770MHz to 780 MHz (China)
868M band:868MHz to 870 MHz (China, EU, USA)
888 MHz to 889 MHz (Australia)
915M band: 902MHz to 928 MHz (USA)
APPLICATIONS
Ultra low-power wireless applications
operating in the 315/433/868/915 MHz ISM/SRD bands
Wireless alarm and security systems
Industrial monitoring and control
Wireless sensor networks
AMR – Automatic Meter Reading
Home and building automation
Wireless MBUS
Arduino
Useful Link:
CC1101 datasheet