Reference: DWM14042301
Spring antenna is specialized for wireless data transmission. This antenna with good performance of V.S.W.R, small size design, easily installation, stable performance and good anti-shock and anti-aged compatible for Hoperf Modules.
Reference: DWM14032902
SMA rf antenna connector is pallets copper gold andexternal thread needle sma pallets plate rf connector.
Reference: DWM14032102
Whip antenna for sub-1 GHz, 433MHz,868MHz and 915MHz with SMA male connectors.it's used with wireless module recommanded by Hoperf .
Reference: DWM14042401
SMA RG178 extension female cable for GPS, GSM antenna,RF module, SMA cable,IPEX to SMA jumper cable.
Reference: DWM18032302
USD3.0/pcs MOQ100pcs LoRa Antenna designed for Lora application which required for outdoor waterproof highgain and work at ISM free band like 433MHz /868MHz /915MHz SMA Male Whip antenna.
Reference: DWM16121503
DWM-TLB-3.0QB SUB-1GHz / 2.4GHz Whip antenna with a Collapsible SMA male connectors.Which are available for 433MHz,868MHz.915MHz and 2.4GHz..
Reference: DWM17111002
LoRa Antenna-433MHz High Gain internal aerial piamater FPC Antenna with IPEX connctor.
Reference: DWM15101001
Brand: Semtech
RFM50 module series’ design is based on the high performance RF50 SoC chip, It include a CIP-51 core‘ MCU and 100mW transceiver. It operate at 433/470/868/915 MHz ISM band, comply with FCC, ETSI regulation.
Low cost Ultrasonic Module HC-SR04 Distance Measuring Transducer Sensor For Arduino.
Features:
100% Brand New.
Size: Approx 45 x 20 x 17mm(L x W x H)
Working Voltage: 5V(DC)
Static current: Less than 2mA.
Output signal: Electric frequency signal, high level 5V, low level 0V.
Sensor angle: Not more than 15 degrees.
Detection distance: 2cm-450cm.
High precision: Up to 0.3cm
Input trigger signal: 10us TTL impulse
Echo signal: output TTL PWL signal
Mode of connection: 1.VCC / 2.trig(T) / 3.echo(R) / 4.GND
Supply module with 5V, the output will be 5V while obstacle in range, or 0V if not. The out pin of this module is used as a switching output when anti-theft module, and without the feet when ranging modules.
Note : the module should be inserted in the circuit before been power, which avoid producing high level of misoperation; if not, then power again.
Adopt IO trigger through supplying at least 10us sequence of high level signal.
The module automatically send eight 40khz square wave and automatically detect whether receive the returning pulse signal.
If there is signals returning, through outputting high level and the time of high level continuing is the time of that from the ultrasonic transmitting to receiving. Test distance = (high level time * sound velocity (340M/S) / 2.
Note: This module is not suitable to connect with electric power, if you need to connect this module with electronic power, then let the GND terminal of this module to be connected first, otherwise, it will affect the normal work of the module.
Package Content
1 x Ultrasonic Module Measuring Transducer Sensor for Arduino
Reference: DWM14032106
The Arduino Uno Rev3 is a microcontroller board based on the ATmega328.
Reference: DWM14101902
Low cost New Temperature and Relative Humidity Sensor DHT11 Module, Arduino adope Temperature and Humidity Sensor module.
Reference: DWM23050401
45 sensor modules In 1 Sensor Kits for Arduino Beginner Learning DIY project.
Reference: DWM23031202
ZH03B PM2.5 Dust Sensor Particle sensor is widely used in air quality monitoring equipment, air purifiers, ventilation systems, air conditioner, and smart home equipment.
Reference: DWM22101701
DWM-M702 seven-in-one sensor module is a cost-effective digital serial port output sensor module, which adopts 485/UART output mode and integrates CO2, HCHO, TVOC,PM2.5,PM10, temperature and humidity.
Reference: DWM18121802
DWM-WWR Spot new weather station wind speed sensor wind direction and rainfall Internet of things Secondary development .
Reference: DWM14032107
The HP203B / HP206C are 24Bit Barometer sensor, employs a MEMS pressure sensor with an I2C interface to provide accurate temperature, pressure or altitude data.
Reference: DWM23031001
ZPHS01 module integrates Electrochemical formaldehyde,Semiconductor VOC sensor, Laser particle sensor, NDIR CO2 sensor and temperature& humidity sensor.
Reference: DWM23031201
MH-Z19 MH-Z19C IR Infrared CO2 Sensor Module Carbon Dioxide Gas Sensor NDIR for CO2 Monitor 400-5000ppm.
Reference: DWM18021501
37 sensor modules In 1 Sensor Kits great package for Arduino Raspberry Pi Beginner Learning.
Reference: DWM23030701
MH-Z19E NDIR infrared gas module Built-in temperature compensation; and it has UART output and PWM output It uses the principle of non-dispersive infrared (NDIR) to detect CO2 in the air and has good selectivity. No oxygen dependence, long life, etc.
Reference: DWM240813
The Sensor Modules pack includes a range of sensors for sensing environmental conditions (temperature, humidity, barometer pressure, lighting), location and movement conditions (GNSS location, accelerometers, and movement detection), soil monitoring, and many more specific sensors (Radar, fingerprint, Infrared, UV, etc.).
Reference: DWM15081101
The TSL2561 Luminosity Sensor Breakout is a sophisticated light sensor which has a flat response across most of the visible spectrum.
Low cost Ultrasonic Module HC-SR04 Distance Measuring Transducer Sensor For Arduino.
