Reference: DWM14042301
Spring antenna is specialized for wireless data transmission. This antenna with good performance of V.S.W.R, small size design, easily installation, stable performance and good anti-shock and anti-aged compatible for Hoperf Modules.
Reference: DWM14032902
SMA rf antenna connector is pallets copper gold andexternal thread needle sma pallets plate rf connector.
Reference: DWM14032102
Whip antenna for sub-1 GHz, 433MHz,868MHz and 915MHz with SMA male connectors.it's used with wireless module recommanded by Hoperf .
Reference: DWM14042401
SMA RG178 extension female cable for GPS, GSM antenna,RF module, SMA cable,IPEX to SMA jumper cable.
Reference: DWM18032302
USD3.0/pcs MOQ100pcs LoRa Antenna designed for Lora application which required for outdoor waterproof highgain and work at ISM free band like 433MHz /868MHz /915MHz SMA Male Whip antenna.
Reference: DWM16121503
DWM-TLB-3.0QB SUB-1GHz / 2.4GHz Whip antenna with a Collapsible SMA male connectors.Which are available for 433MHz,868MHz.915MHz and 2.4GHz..
Reference: DWM17111002
LoRa Antenna-433MHz High Gain internal aerial piamater FPC Antenna with IPEX connctor.
Reference: DWM15101001
Brand: Semtech
RFM50 module series’ design is based on the high performance RF50 SoC chip, It include a CIP-51 core‘ MCU and 100mW transceiver. It operate at 433/470/868/915 MHz ISM band, comply with FCC, ETSI regulation.
ATmega328P LoRa Radio Node is based on SX1276/SX1278 which use the Arduino pro mini 8Mhz 3.3V bootloader, usage same as the Arduino pro mini.
The LoRa Radio Node v1.0 based on the ATmega328P and Sx1276 or Sx1278 radio module. The main chip ATmega328P clocked at 8 MHz and at 3.3V logic, which use the Arduino pro mini 8Mhz 3.3V bootloader, usage same as the Arduino pro mini. This chip has 32K of flash and 2K of RAM.
On board with a 3.7V 14500 battery holder, so it can use anywhere you like. In this LoRa Radio Node, we break out 2 IIC ports, 2 analog port (A0 A1) and 2 digital port (D3 D4) with 4 pin and 3 pin 2510-I type header.
Power supply: 3.7V 14500 Lipo battery or 3.7-12V DC power(VCC GND: 2PIN 2510-I Type connect)
Size: 40mm x 60mm
ATmega328P @ 8MHz with 3.3V logic/power
3.3V regulator with 500mA peak current output
Hardware Serial, hardware I2C, hardware SPI support
1 x PWM pins: D3
12 x analog inputs: A0 A1
Pin #13 BLUE LED for general purpose blinking
2 mounting holes
Reset button
This LoRa Radio Node uses the extra space left over to add a Sx1276(868MHz,915MHz) or Sx1278(433MHz) radio module.
These radios are not good for transmitting audio or video, but they do work quite well for small data packet transmission when you need more range than 2.4 GHz (BT, BLE, WiFi, ZigBee).
SX1276 /SX1278 LoRa® based module with SPI interface
Packet radio with ready-to-go Arduino libraries
Uses the amateur or license-free ISM band: ITU "Europe" license-free ISM or ITU "American" amateur (with amateur band limitations)
+5 to +20 dBm up to 100 mW Power Output Capability (power output selectable in software)
~300uA during full sleep, ~120mA peak during +20dBm transmit, ~40mA during active radio listening.
Simple wire antenna or spot for uFL connector
LoRa Radio Node v1.0
IPEX interface Spring antenna
Reference: DWM19011502
The OLG01-N is an Water proof outdoor setting open source single channel LoRa Gateway. It lets you bridge LoRa wireless network to an IP network via WiFi, Ethernet, 3G or 4G cellular.
Reference: DWM23122503
TrackerD-LS is an Open Source LoRaWAN Asset Tracker based on ESP32 MCU get the location data via GPS and set it to IoT server via LoRaWAN network. supports Motion Detection this feature will save power when no motion is detected.
Reference: DWM14033102
Brand: Semtech
The RFM96W / RFM98W 433MHz,470MHz transceivers feature the LoRaTM long range modem It's from the HopeRF LoRa module.build by the semtech chipset with the application for ARM meters.
Reference: DWM22082508
Ultrasonic Sensors A01A-15,A02-15,A13-15,A16-15 for LDDS04 LoRaWAN 4 channels sensor node.
Reference: DWM23070203
LHT65N-E31F includes a built-in Temperature & Humidity sensor and has an external Sensirion SHT31F high accurancy Temperature & Humidity sensor probe is a Long Range LoRaWAN Sensor.
Reference: DWM22091301
The TrackerD is built-in with GPS, Wi-Fi, BLE, Temperature, Humidity, Motion Detection, and Buzzer which can use Arduino IDE to customize the software for IoT solution.
Reference: DWM20061502
The LWL01 is a LoRaWAN Water Leak Sensor. It detects the water leak status and will send periodically data every day as well as for water leak event. It also count the water leak event times and also calculate last water leak duration.
Reference: DWM23021007
The LHT65S-NE117 Temperature & Humidity sensor is a Long Range LoRaWAN Sensor use an external probe uses TI TMP117A NIST traceability temperature sensor, with 0.1°C accuracy in normal temperature range.
Reference: DWM21031502
The DWM-AR9331 is a minimal system which installed with OpenWrt Linux system and support 2.4G WiFi It is compatible with 802.11b/g/n.widely use as an IoT gateway core modules.
Reference: DWM25022701
The MDS120-LS is a LoRaWAN Microwave Radar distance sensor with a Measure Range: of 15 ~ 1200cm supports BLE configuration and wireless OTA update which makes users easy to use.
Reference: DWM18101201
The OLG02 is an open source dual channels LoRa Gateway. It lets you bridge LoRa wireless network to an IP network via WiFi, Ethernet, 3G or 4G cellular.
Reference: DWM24022602
The PS-LS-I sensors is powered by solar power + li-on battery with an Immersion Installation Type Air Water Pressure sensor which can measure Air, Water pressure and liquid level and upload the sensor data via wireless to the LoRaWAN IoT server.
Reference: DWM23122602
LA66 USB LoRaWAN Adapter v2 is designed to fast turn USB devices to support LoRaWAN wireless features which can easy to add LoRaWAN wireless feature to PC / Mobile phone or an embedded device that has USB Interface.
Reference: DWM22100801
AN-304C LoRaWAN PIR motion sensor node is a wireless infrared alarm which is based on passive infrared technology to detect a motion or occupancy.
Reference: DWM18112201
LoRa Antenna designed for Lora application which required for outdoor waterproof highgain and work at ISM free band like 433MHz /868MHz /915MHz SMA Male Whip antenna.
Reference: DWM22071801
The LSN50v2-D22 is a LoRaWAN Temperature Sensor nodes with two sensor cable which are waterproof, moisture-proof and anti-rust for long-term usage . It can be used to measure the temperature of air, liquid or object.
Reference: DWM17102702
LoRa Antenna designed for Lora application which required for outdoor waterproof highgain and work at ISM free band like 433MHz /868MHz /915MHz SMA Male Whip antenna.
ATmega328P LoRa Radio Node is based on SX1276/SX1278 which use the Arduino pro mini 8Mhz 3.3V bootloader, usage same as the Arduino pro mini.
