Reference: DWM14042301
Spring antenna is specialized for wireless data transmission. This antenna with good performance of V.S.W.R, small size design, easily installation, stable performance and good anti-shock and anti-aged compatible for Hoperf Modules.
Reference: DWM14032902
SMA rf antenna connector is pallets copper gold andexternal thread needle sma pallets plate rf connector.
Reference: DWM14032102
Whip antenna for sub-1 GHz, 433MHz,868MHz and 915MHz with SMA male connectors.it's used with wireless module recommanded by Hoperf .
Reference: DWM14042401
SMA RG178 extension female cable for GPS, GSM antenna,RF module, SMA cable,IPEX to SMA jumper cable.
Reference: DWM18032302
USD3.0/pcs MOQ100pcs LoRa Antenna designed for Lora application which required for outdoor waterproof highgain and work at ISM free band like 433MHz /868MHz /915MHz SMA Male Whip antenna.
Reference: DWM16121503
DWM-TLB-3.0QB SUB-1GHz / 2.4GHz Whip antenna with a Collapsible SMA male connectors.Which are available for 433MHz,868MHz.915MHz and 2.4GHz..
Reference: DWM17111002
LoRa Antenna-433MHz High Gain internal aerial piamater FPC Antenna with IPEX connctor.
Reference: DWM15101001
Brand: Semtech
RFM50 module series’ design is based on the high performance RF50 SoC chip, It include a CIP-51 core‘ MCU and 100mW transceiver. It operate at 433/470/868/915 MHz ISM band, comply with FCC, ETSI regulation.
HopeRF DK / EVB RFduino board which is compatible with Arduino UNO R3 and Arduino IDE.
Brief introduction
1.Hoperf modules + Arduino =RFduino
2.The main board are with the controller ATMEGA328P.
3.Released the RFM6X and RFM9X series module library which are compatible with Arduino IDE
4.It's a good way to represent the technique problems to us.
Userfull Link:
HopeRF_RFDK_RFMxx_DEMO_V2.1_operation_manual
RFduino Board & LoRa module as DK board User guide
Reference: DWM14032102
Whip antenna for sub-1 GHz, 433MHz,868MHz and 915MHz with SMA male connectors.it's used with wireless module recommanded by Hoperf .
Reference: DWM14032902
SMA rf antenna connector is pallets copper gold andexternal thread needle sma pallets plate rf connector.
Reference: DWM14041802
HopeRF DK / EVB module kits with number kinds of module which will plug into the DK & EVB board.
Reference: DWM14060701
The TH02 is a digital relative humidity and temperature sensor. This monolithic CMOS IC integrates temperature and humidity sensor elements, an analog-to-digital converter, signal processing, calibration data, and an I2C host interface.
Reference: DWM15011201
Brand: Semtech
The RFM68CW is an ultra-low-cost, FSK or OOK transmitter module suitable for operation in the 433, 868 and 915 MHz licence free ISM bands., the RFM68CW may be used without the requirement for configuration via an MCU. However, in conjunction with a microcontroller, the communication link parameters may be re-configured. Including, output power,...
Reference: DWM14032104
RFM22B /RFM23B is Low cost and have 433MHz /868MHz /915MHZ three versions wireless transceivers HopeRFmodule.it's popular used remoter controller,Tag readers,UAV RF Modems,the core chipset is SI4432 and it's from the Silicon labs.
Reference: DWM15081807
The CMT2257AW is HopeRF CMT single-chip, ultra low power and high performance device that consists of an OOK/(G)FSK RF receiver, with 1920, 1527 and 2262 embedded data Decoder and 4 data output pins for various 300 to 960 MHz wireless applications.
Reference: DWM15070102
The RFM119SW is a high performance, highly flexible, low-cost, single-chip (G)FSK/OOK transmitter for various,240 to 960 MHz wireless applications.
Reference: DWM23013001
RFM119B is a RF module with which +20dBm high power and high performance thus to support 127 to 1020 MHz frequency, OOK, (G) FSK modulation.
Reference: DWM16050801
HM-TRP series module is one of the hopeRF data link rf module with operating at 433MHz/868MHz/915 MHz and TTL/RS232/RS485 UI is a low cost, high performance transparent FSK transceiver.
Reference: DWM15081804
The CMT2250AW is HopeRF CMT single-chip, ultra low power and high performance device that consists of an OOK RF receiver, with 1920, 1527 and 2262 embedded data Decoder and 4 data output pins for various 300 to 480 MHz wireless applications.
Reference: DWM14033102
Brand: Semtech
The RFM96W / RFM98W 433MHz,470MHz transceivers feature the LoRaTM long range modem It's from the HopeRF LoRa module.build by the semtech chipset with the application for ARM meters.
Reference: DWM21030905
Brand: Semtech
RFM69HW are built-in by SX1231 which is ISM Free band transceiver module capable of operation over a wide frequency range, including the 433MHz,868MHz and 915MHz.
Reference: DWM16110101
The HP203B is 24Bit Barometer sensor, employs a MEMS pressure sensor with an I2C interface to provide accurate temperature, pressure or altitude data.
Reference: DWM15081806
The CMT2157AW is HopeRF CMT single-chip, highly flexible, high performance, OOK/(G)FSK RF transmitter with 1920, 1527 and 2262 data encoder ideal for 240 to 960 MHz wireless applications.
Reference: DWM19072201
HP303S is a miniaturized Digital Barometric Air Pressure Sensor with a high accuracy and a low current consumption, capable of measuring both pressure and temperature.
Reference: DWM15011301
Brand: Semtech
The RFM67W is a fully integrated transmitter which can operate in the 434MHz, 868MHz and 915 MHz licence free ISM bands.suited for the European (ETSI EN300-220-1), North American (FCC part 15.231, 15.247 and 15.249) and Japanese (ARIB T-67) regulatory standards.
Reference: DWM21030904
Brand: Semtech
RFM69HCW are built-in by SX1231H which is ISM Free band transceiver module capable of operation over a wide frequency range, including the 433MHz,868MHz and 915MHz.
Reference: DWM15082002
The CMT2213AW is an ultra low power, high performance, low-cost (G)FSK stand-alone RF receiver for various 300MHz to 480 MHz wireless applications.
Reference: DWM22093002
CMT2300A is an ultra-low power, high performance, OOK (G) FSK RF transceiver suitable for a variety of 140 to 1020 MHz wireless applications.
HopeRF DK / EVB RFduino board which is compatible with Arduino UNO R3 and Arduino IDE.
