Reference: DWM14042301
Spring antenna is specialized for wireless data transmission. This antenna with good performance of V.S.W.R, small size design, easily installation, stable performance and good anti-shock and anti-aged compatible for Hoperf Modules.
Reference: DWM14032902
SMA rf antenna connector is pallets copper gold andexternal thread needle sma pallets plate rf connector.
Reference: DWM14032102
Whip antenna for sub-1 GHz, 433MHz,868MHz and 915MHz with SMA male connectors.it's used with wireless module recommanded by Hoperf .
Reference: DWM14042401
SMA RG178 extension female cable for GPS, GSM antenna,RF module, SMA cable,IPEX to SMA jumper cable.
Reference: DWM18032302
USD3.0/pcs MOQ100pcs LoRa Antenna designed for Lora application which required for outdoor waterproof highgain and work at ISM free band like 433MHz /868MHz /915MHz SMA Male Whip antenna.
Reference: DWM16121503
DWM-TLB-3.0QB SUB-1GHz / 2.4GHz Whip antenna with a Collapsible SMA male connectors.Which are available for 433MHz,868MHz.915MHz and 2.4GHz..
Reference: DWM17111002
LoRa Antenna-433MHz High Gain internal aerial piamater FPC Antenna with IPEX connctor.
Reference: DWM15101001
Brand: Semtech
RFM50 module series’ design is based on the high performance RF50 SoC chip, It include a CIP-51 core‘ MCU and 100mW transceiver. It operate at 433/470/868/915 MHz ISM band, comply with FCC, ETSI regulation.
The LR1262 Development KIT uses RP2040 as the main control and is equipped with the LR1262 module that supports Lora and LoRaWAN protocols to help users realize LoRa and LoRaWAN applications.
The LR1262 Development KIT uses RP2040 as the main control and is equipped with the LR1262 module that supports Lora and LoRaWAN protocols to help users realize development. RP2040 is a dual-core, high-performance, low-power ARM Cortex-M0+ architecture chip, suitable for IoT, robots, control, embedded systems, and other applications. The LR1262 Dev Board is an ultra-low remote transceiver module based on the STM32WLE5CC chip, specially designed for LoRa and LoRaWAN applications.
This board retains various functional interfaces for development, such as the Crowtail interface, which can adapt to Crowtail module series, the common PIN to PIN header that leads out GPIO ports, and provides 3.3V and 5V outputs, suitable for the development and use of commonly used sensors and electronic modules on the market. In addition, the board also reserves RS485 interface, SPI, I2C, and UART interfaces, which can be compatible with more sensors/modules.
In addition to the basic development interfaces, the board also integrates some commonly used functions, such as a buzzer, a custom button, red-yellow-green three-color indicator lights, and a 1.8-inch SPI interface LCD screen with a resolution of 128*160. We try to minimize the trouble of connecting these components for users when developing and building project prototypes.
Uses RP2040 as the main controller, with two 32-bit ARM Cortex M0+ processor cores (dual-core), and provides more powerful performance
Integrates the LR1262 module support the 868/915MHz frequency band and AT command control
Abundant external interface resources, compatible with Crowtail series modules and other common interface modules on the market
Integrates commonly used functions buzzer, LED light, LCD, and custom button, making it more concise and convenient when creating projects
Onboard 1.8-inch 128*160 SPI-TFT-LCD, ST7735S driver chip
Compatible with Arduino/Micropython, easy to carry out different projects.
Raspberry Pi chip RP2040, built-in 264KB SRAM, onboard 4MB Flash
Dual Core Arm Cortex-M0+ @ 133MHz
LR1262 Supports frequency band
803MHZ-930MHZ
LR1262 Support Interface
External antenna, SMA interface or IPEX first-generation interface
Onboard 1.8-inch 128*160SPI-TFT-LCD
LCD Resolution
128*160
LCD Driver
ST7735S (4-wire SPI)
Development environment
Arduino/Micropython
1x RS485 communication interface,
8x 5V Crowtail interfaces (2x analog interfaces, 2xdigital interfaces, 2xUART interfaces, 2xIIC interfaces)
12x 5V universal pin header IO interfaces
14x 3.3V universal pin header IO interfaces
1x 3.3V/5V switchable SPI interface
1x 3.3V/5V switchable UART interface
3x 3.3V/5V switchable IIC interfaces
Buttons and functions
1x passive buzzer,
4x user-defined buttons,
6x programmable LEDs
USB 5V-1A
-10°C ~ 65°C
102mm(L)x76.5mm(W)
| RP2040 | LR1262 Development Board | ||
| GPIO0 | LR1262-RXD | GPIO15 | GPIO15/ Crowtail-D1 |
| GPIO1 | LR1262-TXD | GPIO16 | LCD-DC |
| GPIO2 | GPIO2 | GPIO17 | LCD-CS |
| GPIO3 | GPIO3 | GPIO18 | LCD-SCK |
| GPIO4 | Crowtail-UART1-TXD | GPIO19 | LCD-DIN |
| GPIO5 | Crowtail-UART1-RXD | GPIO20 | I2C0-SDA0/Crowtail-I2C-SDA/PCA9555-SDA |
| GPIO6 | GPIO6 | GPIO21 | I2C0-SCL0/Crowtail-I2C-SCL/ PCA9555-SCL |
| GPIO7 | GPIO7 | GPIO22 | LCD-RST |
| GPIO8 | GPIO8/UART1-TX1/Crowtail-UART1-TX1/485TX | GPIO23 | LCD-BLK |
| GPIO9 | GPIO9/UART1-RX1Crowtail-UART1-RX1/485RX | GPIO24 | 485-EN |
| GPIO10 | GPIO10/SPI1-SCK | GPIO25 | DATA |
| GPIO11 | GPIO11/SPI1-MOSI | GPIO26 | A0/ Crowtail-A0 |
| GPIO12 | GPIO12/SPI1-MISO | GPIO27 | A1/ Crowtail-A1 |
| GPIO13 | GPIO13/SPI1-CS | GPIO28 | BUZZER |
| GPIO14 | GPIO14/ Crowtail-D0 | GPIO29 | ADC-KEY |
1x LR1262 Development Board
1x Lora Spring Antenna (868Mhz/915Mhz)
1x Lora Rubber Antenna (868Mhz/915Mhz)
Reference: DWM22082503
RAK11300 is based on the Raspberry Pi RP2040 chip and SX1262 RF transceiver it's complies with Class A & C of LoRaWAN 1.0.2 specifications.
Reference: DWM23010502
HTIT-Wsh ESP32-S3 SX1262 WIFI BLE LoRa/ LoRaWAN Wireless Shell-V3 provides Wi-Fi, BLE, and LoRa solutions, which perfectly support Arduino development environment.
Reference: DWM25030701
The nRFLR1262 module integrates the Nordic nRF52840 microcontroller and the Semtech SX1262 LoRa transceiver chip supports Bluetooth 5.3 and low-power Bluetooth and complies with the A, B, and C classes of the LoRaWAN 1.0.3 specification. It also supports the LoRa point-to-point (P2P) communication mode.
Reference: DWM25030801
The ThinkNode-G1 LoRaWAN indoor gateway supports multiple connection methods such as WiFi, Bluetooth, and Ethernet, and supports 8-channel Lora transmission.
Reference: DWM24012302
The SunFounder Raspberry Pi Pico W Ultimate Starter Kit offers a rich IoT learning experience for beginners aged 8+. With 450+ components,117projects, and expert-led video lessons, this kit makes learning microcontroller programming and IoT engaging and accessible.
Reference: DWM20030406
The A9G development board is a multifunctional development board based on EMC’s A9G GPRS/ GSM + GPS/ BDS module it can be used Wireless Data Transmission and Positioning IOT Development.
Reference: DWM17080704
MTH02 Digital Temperature & Humidity Sensor is Japan's Hokuriku resistive humidity sensor production as a Temperature & Humidity sensor.
Reference: DWM25031701
The ThinkNode-M1 uses nRF52840 as the main processor Combined with the SX1262 wireless chip which is perfectly compatible with the Meshtastic official App to configure and manage device parameters, message communication, map and location sharing, network status monitoring, data recording and exporting, custom settings, etc.
Reference: DWM16121103
Easy Pulse is a DIY pulse sensor that can be used for detecting the cardio-vascular pulse wave from a fingertip.
Reference: DWM17072502
D-duino is a combination of ESP8266 and OLED is a 6 IOT WiFi NodeMCU Development Board .
Reference: DWM17072501
ESP8266 Evaluation Board ESP-12 is full WIFI evalution board which mounted on a PCB with all the GPIO broken out,each GPIO has an LED connected so you can quickly test your code without connecting external hardware, and a LDR to test the ADC.
Reference: DWM17080703
AM2321 is a temperature and humidity composite sensor that contains calibrated digital signal output, using special temperature and humidity sensor acquisition technology to ensure that products with high reliability and excellent long-term stability.
Reference: DWM25031002
The LR1302-PI HAT is a Raspberry Pi expansion board that connects the SX1302-based LR1302 LoRaWAN gateway module to a Raspberry Pi Support Raspberry Pi 5/Support Raspberry Pi 4 B / Support Raspberry Pi 3 A+/B/B+ / Support Raspberry Pi 2 B / Support Raspberry Pi A+/B+.
Reference: DWM25031001
The LR1302 LoRaWAN Gateway Module is based on the SX1302 Long Range Gateway Module. It Supports 8 Channels with an SPI user interface and adopts a mini-PCIe form design and features.
Reference: DWM25031403
The LR1262 Development Board uses RP2040 as the main controller and LR1262 module users combined with the sensor modules have UI Ax2/Dx2/IICx1/UARTx1 that can quickly build a Lora node.
Reference: DWM17080701
AM2301 DHT21 Capacitive Digital Temperature & Humidity Sensor is wired with DHT21 or AM2301 sensors.
Reference: DWM17080702
BMP180 Barometer Pressure /Temperature /Altitude Sensor is a low-cost sensing solution for measuring barometric pressure and temperature and altitude.
Reference: DWM25031101
The nRFLR1110 module Integrates nRF52840 and LR1110 supports Bluetooth 5.3, LoRaWAN1.0.4, and built-in high-performance GNSS tracking function it also supports network protocols such as Bluetooth mesh, NFC, Threa,d, and Zigbee.
Reference: DWM25030701
The nRFLR1262 module integrates the Nordic nRF52840 microcontroller and the Semtech SX1262 LoRa transceiver chip supports Bluetooth 5.3 and low-power Bluetooth and complies with the A, B, and C classes of the LoRaWAN 1.0.3 specification. It also supports the LoRa point-to-point (P2P) communication mode.
Reference: DWM20030402
EasyESP-1 WiFi-enabled ESP8266 microcontroller is a rapid prototyping and development board for the low-cost, specially designed for beginners.
The LR1262 Development KIT uses RP2040 as the main control and is equipped with the LR1262 module that supports Lora and LoRaWAN protocols to help users realize LoRa and LoRaWAN applications.
