Reference: DWM14042301
Spring antenna is specialized for wireless data transmission. This antenna with good performance of V.S.W.R, small size design, easily installation, stable performance and good anti-shock and anti-aged compatible for Hoperf Modules.
Reference: DWM14032902
SMA rf antenna connector is pallets copper gold andexternal thread needle sma pallets plate rf connector.
Reference: DWM14032102
Whip antenna for sub-1 GHz, 433MHz,868MHz and 915MHz with SMA male connectors.it's used with wireless module recommanded by Hoperf .
Reference: DWM14042401
SMA RG178 extension female cable for GPS, GSM antenna,RF module, SMA cable,IPEX to SMA jumper cable.
Reference: DWM18032302
USD3.0/pcs MOQ100pcs LoRa Antenna designed for Lora application which required for outdoor waterproof highgain and work at ISM free band like 433MHz /868MHz /915MHz SMA Male Whip antenna.
Reference: DWM16121503
DWM-TLB-3.0QB SUB-1GHz / 2.4GHz Whip antenna with a Collapsible SMA male connectors.Which are available for 433MHz,868MHz.915MHz and 2.4GHz..
Reference: DWM17111002
LoRa Antenna-433MHz High Gain internal aerial piamater FPC Antenna with IPEX connctor.
Reference: DWM15101001
Brand: Semtech
RFM50 module series’ design is based on the high performance RF50 SoC chip, It include a CIP-51 core‘ MCU and 100mW transceiver. It operate at 433/470/868/915 MHz ISM band, comply with FCC, ETSI regulation.
The E931.96 is an ultra-low power motion detector controller integrated circuit. The device is ideally suited for battery operated wireless motion sensors that make use of an MCU for handling com munication.
General Description
The E931.96 is an ultra-low power motion detector controller integrated circuit. The device is ideally suited for battery operated wireless motion sensors that make use of an MCU for handling communication. The MCU does not need to be active while the E931.96 does continuous motion sensing. It only activates the external controller, when motion is detected. Motion is signaled through the push-pull
output (INT). The criteria for motion detection are programmable and can be changed by the external controller.
The E931.96 interfaces directly with up to two conventional PIR sensors via a high impedance differential input. The PIR signal is converted to a 14bit digital value on chip. All signal processing is performed digitally.The E931.96 is available in a SOIC-8 package.
Useful Link：E931.96 Ultra-Low Power PIR Controller Integrated Circuit.
Software development guide for E931.96, Reading and Writing functions
Applications
Wireless intruder detectors
Battery powered door chimes
Emergency lighting
Motion and presence detection
Features
Programmable detection criteria and operating
modes
Digital signal processing
On chip supply regulator for conventional PIR
detectors
Ultra Low power consumption
Differential PIR sensor input
Supply voltage measurement
Temperature measurement
Instantaneous settling after power up
Reference: DWM14092802
HC-SR501 is Adjust IR Pyroelectric Infrared PIR module Motion Sensor Detector Module for arduino.
Reference: DWM14092801
DWM-PM-2 Mini Infrared PIR module PIR motion sensor module with LDR work mode.
Reference: DWM17031001
DWM-PM-8 50uA Lowest standby Current 0.18s to 300s Delay Time Mini Infrared PIR module with LDR work mode.
Reference: DWM20041502
M5StickC PIR Hat detect the infrared come from the human body.
Reference: DWM17020801
DWM-PM-6 20uA Lowest standby Current 1.8s to 1Hour Delay Time Mini Infrared PIR module with LDR work mode.
Reference: DWM14092801
DWM-PM-2 Mini Infrared PIR module PIR motion sensor module with LDR work mode.
Reference: DWM14092802
HC-SR501 is Adjust IR Pyroelectric Infrared PIR module Motion Sensor Detector Module for arduino.
The E931.96 is an ultra-low power motion detector controller integrated circuit. The device is ideally suited for battery operated wireless motion sensors that make use of an MCU for handling com munication.
