All best sellers
  • On sale!
FRS-DEMO-B UHF/ VHF Walkie Talkie transceiver and Data transfer demo board
  • FRS-DEMO-B UHF/ VHF Walkie Talkie transceiver and Data transfer demo board

FRS-DEMO-B UHF/ VHF Walkie Talkie transceiver and Data transfer demo board

DWM18012602

FRS-DEMO-B UHF/ VHF Walkie Talkie transceiver and Data transfer demo board which can be used for these module evaluation SR-FRS-1WU,SR-FRS-1WV,SR-FRS-2WU.

Part Number

Volume discounts

Quantity Unit discount You Save
4 $1.00 Up to $4.00
6 $2.00 Up to $12.00
10 $3.00 Up to $30.00
$35.00
Tax excluded
Quantity

The minimum purchase order quantity for the product is 2.

Description

1. Outline
FRS-DEMO-B  is designed for Walkie Talkie transceiver module demo as below:
SR_FRS_0W5U:  0.5W/400M-480M
SR-FRS-1W350:  1W/350M-390M
SR-FRS-1WU:    1W/400M-480M
SR_FRS_1WV:   1W/136M-174M
SR-FRS-2WU:    2W /400M-480M

 it can be used for voice intercom and data transfer  demonstration; also it can be used for development based on the demo board;
 it is easy to set all the module parameter via the USB interface; When select the channel, it would voice broadcast the current channel number; You may quickly evaluate our module performance by the demo board, Just make a little modify, it can be directly applied into your real production.

2.  The Demo board performance:
1)  It has the power switch, volume adjust , Channel selection switch ;
       16 channels can be selected by the encoder switch;  
2)  It is easy to switch the VOX(Sound control transmit) by a VOX switch, the VOX level can be set via the PC;
3)  Voice broadcast for the channel number, Chinese/English could be selected. 
4)  Monitor function by press [MON]key;
5)  Voice intercom demo;
6)  Data transfer demo;
7)  One group user interface: SQ, LINE_IN,  LINE_OUT, PTT,  GND
8)  Could restore to the factory  parameter setting
9)  The demo board parameter can be set via the USB interface, for the setting instruction please contact us to get the 《serial communication protocol》 
 Tx frequency, Rx frequency can be set alone;
 Tx CTCSS, Rx CTCSS can be set alone;
 Rf output power can be set by software;
 Companding setting;
 Transmit Busy lock setting;
 Squelch level setting
 GBW bandwidth setting
 MIC sensitivity setting
 Scramble setting
 Volume setting
 VOX level setting
 TOT setting(Timer of transmit)
 Auto power save setting
 Data transfer
 All setting can be kept when power off
3.  The demo board function define picture

 1) The demo board size:45mm X 90 mm;
 2) DC power supply:3.3V-5V;
 3) USB type: MICRO USB;
 4) User interface:SQ, Line _in, Line_out, PTT, GND;
    When use Line_in,Should push the MIC selection to  “EXT”position;
 5) LED:
      Red led: DC power indication;
      Yellow: Transmit status indication
      Blue:  Receive signal indication

4.  The demo board operation


4.1  The voice intercom
1. Please mount the power, antenna, speaker; Push the MIC select switch to ‘INT’ position;
2. Power on the demo board , the power indication LED(red) turns on, Then rotate the volume adjust switch to a proper position; After about 1seconds, the demo board would voice broadcast the current channel number;
3. Adjust the channel selection switch, ensure the transmitter and receiver are at the same channel;
4. Hold on the [PTT] key, the transmit indication LED(yellow) turns on, You may talk to the opposite side; After finished the talking, release the [PTT] key, the system automatically into the receive statues, When received the signal from the opposite side, The receive indication LED(blue)turns on;
5. At weak signal area, you may hold on the[MON] key, the system into monitor mode, release the [MON]key, the monitor mode is cancelled;
6. The frequency and the CTCSS for every channel can be set alone via the USB interface;


4.2  The sound control(VOX) 
1. Push VOX switch to ON position, the VOX function is enabled, You may talk without [PTT]key, the system will automatically into transmit status.;
2. During the VOX valid status,The transmit indication LED(Yellow) turns on;
When VOX enabled, the [PTT] key is still valid;
3. Push VOX switch to OFF position, the VOX function is disabled, you can only intercom by press the [PTT] key;
4. The VOX sensitivity can be set via the USB interface;

 

4.3 User interface
1.  The demo board provide some useful interface for the user
     SQ:   0: with valid receive signal; 1: without receive signal;
     Line_in: May connect to an external Microphone, or an external audio source;
     MIC select switch” must at the “EXT” position;
     Line_out:The Frs module audio frequency directly output, Not via the audio amplify;
     PTT:    0: Transmit; 1:Receive;
    GND:   GND;

 

4.4 Restore to the factory setting
1. Power off;
2. Press the [PTT] and hold on, then Power on; When the transmit indicate LED fast blink, you may release[PTT] key;
3. When finished the system initialization,Transmit indication LED turns off,The system into the standby mode;


4.5  Data transfer/SMS transfer
1. Connect the Demo board USB and the PC usb by MICRO USB cable;
2. Send command:AT+DMOMES=[Length]xxxxxxxxxxx
3. For the detail of the command ,please refer the UART communication protocol;
4. For how to make the data transfer please refer “4.7 USB interface for parameter setting”


4.6 USB interface for parameter setting
1. Firstly, you must install the USB driver,please download from the link:
https://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225&pcid=41
NOTES: The USB 2 COM chip for this demo board is PL2303HX, it can only support the OS to WIN7, if you want support the OS to WIN8, please replace the PL2303HX with PL2303TA;

2.  Power on the demo board, Connect the demo board and the PC with the Micro USB cable.

3.  PC COM port setting
     Serial port;May be COM1,COM2.COM3…. etc. 
     Baut: 9600 only;
     Parity:None 
     Data:8
     stop:1

4.  Frs module parameter setting
Here is a example for GROUP COMMAND Setting:
AT+DMOSETGROUP=0,450.0500,450.0500,0,2,0,0 
(An “Enter” must be added at the end of the command)
The parameter contents are as below in turn:
       0:Narrow
       450.0500:Transmit frequency( MHZ)
       450.0500:Receive frequency ( MHZ)
       0:Receive CTCSS
       2:Squelch level
       0:Transmit CTCSS
       0:Rf output power and etc. :

Comment:
1) The Tx Frequency and Rx Frequency can be set alone.
2) The Tx CTCSS and Rx CTCSS  can be set alone.
3) The parameter can’t be kept because of this demo board without MCU.

2-1.png

      At the end of the command, a “enter” must be done then click the “send”; 
      If the command is sent correctly, then the module returns  
     +DMOSETGROUP:0    to the receive area

 The other parameter setting is same as the Group setting, Please refer 《Serial communication protocol》 
4)  Short message / Data transfer 
     Prepare 2 sets PC, All the PC must connect the demo board correctly;
     Suppose PC1 as the data transfer,and PC2 as the data receiver;

Transfer data by PC1:
  a) Input the command with Text format ( Don’t check the “Send as hex”)
  AT+DMOMES=7ABCDEFG
 (must click “Enter” key once from the keyboard)

2-2.png 

 Because the SMS length should be Hex,  The command should be converted into HEX format, And modify the Length manually.
  
b)  Check the item of serial tool“Send as HEX”
Now the command of text format is converted to HEX format automatically;
41 54 2B 44 4D 4F 4D 45 53 3D 37 41 42 43 44 45 46 47 0D 0A
The “37” Should be modified to be “07” manually , because the Length Byte is Hex;
The right command should be:
41 54 2B 44 4D 4F 4D 45 53 3D 07 41 42 43 44 45 46 47 0D 0A

2-3.png

c) Click “Send”
d) Once the message is sent correctly by module,The module would report the transfer results to PC, that is , the contents as below would be displayed on PC1.
+ DMOMES:0

      Receive data by  PC2:
          Once received a message /data , The receive area would display as below:

a) When not check“Receive as HEX” ,The display contents would be: +DMOMES=*ABCDEFG

2-4.png

 

b) When check “Receive as HEX” ,The display contents would be:
2B 44 4D 4F 4D 45 53 3D 07 41 42 43 44 45 46 47 0D 0A

 

2-5.png

 

5.  The default parameter for demo board:

5.1 UHF(400M-480M) demo board

  1. Band widthNarrow;

  2. Squelch level: 2;

  3. VOX sensitivity6

  4. MIC sensitivity6

  5. Volume6

  6. ScrambleOFF

  7. Tx output power1W (valid only for SR_FRS_1W) ;

  8. CompandingOFF

  9. Busy lockOFF

  10. TOT(Timer of Transmit)3minutes

  11. The default frequency and CTCSS

Channel

Transmit

frequency

MHZ

Receive frequency

(MHZ)

Transmit

CTCSS

Receive

CTCSS

1

450.0500

450.0500

0

0

2

450.0750

450.0750

0

0

3

450.1000

450.1000

0

0

4

450.1250

450.1250

0

0

5

450.1500

450.1500

0

0

6

450.1750

450.1750

0

0

7

450.2000

450.2000

0

0

8

450.2250

450.2250

0

0

9

450.2500

450.2500

0

0

10

450.2750

450.2750

0

0

11

450.3000

450.3000

0

0

12

450.3250

450.3250

0

0

13

450.3500

450.3500

0

0

14

450.3750

450.3750

0

0

15

450.4000

450.4000

0

0

16

450.4250

450.4250

0

0

5.2  VHF(136M-174M)demo board

  1. Band widthNarrow;

  2. Squelch level: 2;

  3. VOX sensitivity6

  4. MIC sensitivity6

  5. Volume6

  6. ScrambleOFF

  7. Tx output power1W (valid only for SR_FRS_1W) ;

  8. CompandingOFF

  9. Busy lockOFF

  10. TOT(Timer of Transmit)3minutes

  11. The default frequency and CTCSS

Channel

Transmit

frequency

MHZ

Receive frequency

(MHZ)

Transmit

CTCSS

Receive

CTCSS

1

150.0500

150.0500

0

0

2

150.0750

150.0750

0

0

3

150.1000

150.1000

0

0

4

150.1250

150.1250

0

0

5

150.1500

150.1500

0

0

6

150.1750

150.1750

0

0

7

150.2000

150.2000

0

0

8

150.2250

150.2250

0

0

9

150.2500

150.2500

0

0

10

150.2750

150.2750

0

0

11

150.3000

150.3000

0

0

12

150.3250

150.3250

0

0

13

150.3500

150.3500

0

0

14

150.3750

150.3750

0

0

15

150.4000

150.4000

0

0

16

150.4250

150.4250

0

0


6.The standard FRS frequency assignment

Channel

China

MHZ

American

(MHZ)

European

(MHZ)

Australia

(MHZ)

1

409.7500

462.5625

446.00625

476.625

2

409.7625

462.5875

446.01875

476.650

3

409.7750

462.6125

446.03125

476.675

4

409.7875

462.6375

446.04375

476.700

5

409.8000

462.6625

446.05625

476.725

6

409.8125

462.6875

446.06875

476.750

7

409.8250

.462.7125

446.08125

476.775

8

409.8375

467.5625

446.09375

476.800

9

409.8500

467.5875

 

476.825

10

409.8625

467.6125

 

476.875

11

409.8750

467.6375

 

476.900

12

409.8875

467.6625

 

476.925

13

409.9000

467.6875

 

477.000

14

409.9125

467.7125

 

477.025

15

409.9250

   

477.050

16

409.9375

   

477.075

17

409.9500

   

477.100

18

409.9625

   

477.150

19

409.9750

     

20

409.9875

     

7.  Comment

1)  About the antenna we sent to you

     For 1W UHF module, The antenna central frequency is 450M + - 3M;

     For 1W VHF module, The antenna central frequency is 150M + - 2M;

The antenna central frequency must be same with the module working frequency, otherwise, it would seriously affect the transmit power and the receive sensitivity;


2)  The demo board is subject to be upgraded without notice, the board you get maybe have some difference with the spec.


Product Details
DWM18012602
50 Items
You might also like
16 other products in the same category:

Reviews

Write your review

FRS-DEMO-B UHF/ VHF Walkie Talkie transceiver and Data transfer demo board

FRS-DEMO-B UHF/ VHF Walkie Talkie transceiver and Data transfer demo board which can be used for these module evaluation SR-FRS-1WU,SR-FRS-1WV,SR-FRS-2WU.

Write your review

Follow us on Facebook